Table of Contents
Advertisement
Operating Instructions and Parts Manual
General Safety
WARNING
!
Information
(Cont'd.)
body contact with
grounded surfaces such as
4. Do not wear jewelry when
pipes, radiators, ranges,
operating any tool. Jewelry may
become caught in moving parts and
and refrigerators. There is an increased
result in serious personal injury.
risk of electric shock if your body is
grounded.
5. Always use attachments designed
for use with this tool. Do not use
WARNING
!
damaged or worn attachments.
•
Never carry tool by its cord.
6. Never trigger the tool when not
•
Never pull the cord to disconnect
applied to a work object.
from receptacle.
Attachments must be securely
1. Make sure cord is located so that it
attached. Loose attachments can
will not be stepped on, tripped over,
cause serious injury.
or otherwise subjected to damage or
7. Never point a tool at oneself or any
stress.
other person. Serious injury could
2. Do not use an extension cord unless
occur.
absolutely necessary. Use of improper
8. Use steady, even pressure when
extension cord could result in a risk of
using tool. Do not force. Too much
fire and electric shock. If an extension
pressure can cause blade to break
cord must be used, make sure:
or overheat.
• That the pins on plug of extension
9. Keep all nuts, bolts and screws tight
cord are the same number, size and
and ensure equipment is in safe
shape as those of plug.
working condition.
• That the extension cord is properly
10. Do not put hands near or under
wired and in good electrical
moving parts.
condition.
WORK AREA
• If an extension cord is to be used
outdoors it must be marked with
WARNING
!
the suffix "W-A" or "W" following
Do not
the cord type designation to
operate a power tool in an
explosive atmosphere,
indicate it is acceptable for outdoor
such as in the presence of
use. For example – SJTW-A
flammable liquids, gases,
3. Do not expose to rain, snow or frost.
or dust. Power tools create
Water entering a power tool will
sparks which may ignite the fumes or
increase the risk of electric shock.
dust.
PERSONAL SAFETY
CAUTION
!
Keep work area
WARNING
!
clean and well lighted. Cluttered
product. Excessive exposure to
benches and dark areas invite
vibration, work in awkward positions,
accidents.
and repetitive work motions can cause
injury to hands and arms. Stop using any
CAUTION
!
tool if discomfort, numbness, tingling, or
Keep bystanders,
pain occur, and consult a physician.
children, and visitors away while
operating a power tool. Distractions
1. Stay alert, watch what you are doing,
can cause you to lose control.
and use common sense when
operating a power tool. Do not use
ELECTRICAL SAFETY
tool while tired or under the
Double insulated tools are equipped with
influence of drugs, alcohol, or
a polarized plug (one plug blade is wider
medication. A moment of inattention
that the other). This plug will fit in a
while operating power tools may
polarized outlet only one way. If the plug
result in serious personal injury.
does not fit fully into the outlet, turn the
CAUTION
!
plug over and insert into plug again.
starting. Be sure switch is in the locked
WARNING
or OFF position before making any
!
Do not expose
adjustments, changing accessories, or
power tools to rain or wet conditions.
storing the tool. Carrying tools with
Water entering a power tool will
your finger on the switch while the
increase the risk of electric shock.
switch is in the ON position invites
accidents.
www.chpower.com
2. Remove adjusting keys or wrenches
before turning ON the tool. A key or
Avoid
wrench attached to a rotating part of
the tool may result in personal injury.
3. Do not overreach. Keep
proper footing and
balance at all times.
Proper footing and
balance enable better
control of the tool in
Do not abuse cord.
unexpected situations.
4. Always work in a well-
ventilated area. Wear an
OSHA-approved dust
mask and safety glasses.
5. Hold tool by insulated gripping
surface when performing an
operation where the tool may
contact hidden wiring. Contacting a
"live" wire will make exposed metal
parts of the tool "live" and shock the
operator.
6. Keep hands away from rotating parts.
7. Use clamps or another practical way
to secure the workpiece to a stable
platform. Never hold work in your
hand, lap, or against other parts of
your body when cutting.
8. Always use blades with correct size
and shape (diamond vs. round) arbor
holes. Blades that do not match the
mounting hardware of the saw will
run eccentrically, causing great risk or
injury to the user and damage to the
tool.
9. NEVER hold piece being cut in your
hands or across your leg. It is
important to support the work
properly to minimize body exposure,
blade binding, or loss of control.
Do not misuse this
10. Wear ear protection
when using the tool for
extended periods.
Prolonged exposure to
high intensity noise can
cause hearing loss.
11. Make sure that all nails have been
pulled from workpiece before
starting cutting operation.
12. This saw is not designed to cut hollow
pipe. Perform cuts on approved
materials only.
13. Do not touch metal parts of saw
while cutting in blind areas. Blind
spots like walls and floors may
Avoid accidental
contain live electric wires.
14. Do not touch metal parts of saw or
blade immediately after use. Parts
will be hot and can cause serious
burn.
2
Mantenimiento
SERVICIO TÉCNICO
(Cont.)
Para obtener información con relación
limpiar la herramienta, evitando todos
al funcionamiento o reparación de
los contactos eléctricos.
este producto, sírvase llamar al
1-800-424-8936.
Ciertos agentes de limpieza y solventes
son nocivos para los plásticos y otras
PRECAUCION
!
piezas aisladas. Algunos de éstos
incluyen gasolina, aguarrás, solvente
El servicio de la herramienta debe
para laca, solvente de pintura,
ser realizado sólo por personal de
solventes de limpieza con cloro,
reparaciones calificado. El servicio
amoníaco y detergentes de uso
o mantenimiento realizado por personas
doméstico que contengan amoníaco.
no calificadas puede provocar riesgo
Nunca use solventes inflamables ni
de lesiones.
combustibles cerca de las herramientas.
Para Ordenar Repuestos o Asistencia Técnica, Llame al Teléfono 1-800-424-8936
Sirvase darnos la siguiente información:
•
Número del modelo
•
Código impreso
•
Descripción y número del repuesto según la lista de repuestos
Dirija toda la correspondencia a:
Campbell Hausfeld
Attn: Customer Service
100 Production Drive
Harrison, OH 45030 U.S.A.
Al realizarle un servicio a la herramienta,
utilice únicamente piezas de repuesto
idénticas. Siga las instrucciones de la
sección Mantenimiento de este manual.
El uso de piezas no autorizadas o el no
seguir las instrucciones de
Mantenimiento puede crear un riesgo
de choque eléctrico o lesión.
Lista de Repuestos
Número del
Descripción
Repuesto
Hoja de la sierra
DG025800AV
Tubo de polvo
DG025900AV
Guía del borde
DG026000AV
Llave Allen de 3mm
DG026100AV
19 Sp
DG460500CK
Advertisement
Table of Contents
