Page 1
PS NB 3/10/21 Assembly Instructions & User’s Manual Tree Stump Gas Fire Pit Item#: 166980 Model#: SRGF22010 ANS Z21.97/CSA 2.41-2017 Outdoor Decorative Gas Appliances Please keep this instruction manual for future reference Warning: READ INSTRUCTION MANUAL BEFORE ATTEMPTING TO ASSEMBLE OR OPERATE THIS PRODUCT.
Page 2
Warnings and Cautions Read the instructions before use. This appliance must be installed in accordance with such regulations as are enforced. INSTALLER: Leave this manual with the appliance. WARNING: For Outdoor Use Only. CONSUMER: Retain this manual for future reference Installation and service must be performed by a qualified installer, DANGER...
Table of Contents Warnings and Safety Information Cautions........2,4-5 Table of Contents...................3 Exploded View..................6 Parts List ....................7 Assembly Instructions................8 Installation Instructions .................9 Operation..................10-12 Maintenance ..................13 Storage ....................14 Troubleshooting ...................15 Warranty Information ................15 REMINDER BEFORE ASSEMBLY Verify that all parts are included with your fire pit BEFORE you begin assembly by checking the Parts and Hardware List.
Warnings and Safety Information Cautions IMPORTANT SAFETY INFORMATION 1. The installation must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1 NFPA 54; National Fuel Gas Code; Natural Gas and Propane Installation Code, CSA B149.1;...
Page 5
Warnings and Safety Information Cautions IMPORTANT SAFETY INFORMATION ABOUT PROPANE (LP) GAS 1. The LP-gas supply cylinder to be used must be constructed and marked in accordance with the U.S. Deparment of Transportation (D.O.T.) Specifications for LP-Gas Cylinders, or the Standard for Cylinders, Spheres and Tubes for Transportation of Dangerous Goods and Commission, CAN/CSA-B339, as applicable.
Exploded View Please check the contents of the packaging to ensure all parts are included. If missing parts please contact customer service. Note: This appliance has already been pre-assembled. Page 6 of 15...
Assembly Instructions Choose a good, cleared assembly area and get a friend to help you put your gas fire pit together. Lay cardboard down to protect gas fire pit finish and assembly area. Open the box of glass rocks, put the glass rocks (D) into the fire bowl of the fire table (A) (see Figure 2). A gas fire pit requires 8.8 lbs glass rocks.
Installation Instructions INSTALLATION Two or more people are helpful for an easier installation. LOCATION Your fire pit must be installed on flat, stable surface, away from any combustible materials or construction. 1. Open the door. Place the gas cylinder into the gas cylinder support and connect the regulator by turning the black handle clockwise to tighten.
Operation WARNING: DO NOT ATTEMPT TO OPERATE THIS APPLIANCE UNTIL YOU HAVE READ AND UNDERSTAND ALL PRECAUTIONS. FAILURE TO DO SO CAN RESULT IN PROPERTY DAMAGE SERIOUS INJURY, OR DEATH. BATTERY Make sure the control knob is in the “OFF” position. Unscrew the push button cap on the ignitor module located on the control panel to access the battery compartment.
Page 11
Operation WARNING: DO NOT ATTEMPT TO OPERATE THIS APPLIANCE UNTIL YOU HAVE READ AND UNDERSTAND ALL PRECAUTIONS. FAILURE TO DO SO CAN RESULT IN PROPERTY DAMAGE SERIOUS INJURY, OR DEATH. gas valve / regulator hose connection (Figure 9) inlet tube / bellows connection (Figure 10) To perform a leak test: 1.
Page 12
Operation TO TURN OFF GAS 1. Push in gas control knob slightly and turn to “OFF”. WARNING: For your safety, read and follow the Lighting Instructions in this manual and in the Rating Plate on the appliance. IMPROPER LIGHTING PROCEDURES COULD RESULT IN A FIRE HAZARD OR EXPLOSION HAZARD OR PROPERTY DAMAGE, INJURY OR LOSS OF LIFE.
Storage Wait until the appliance is completely cool before covering. If storing following immediate usage, allow the fire pit to cool at least 45 minutes before preparing for storage. Once the fire pit is cool and with all valves turned to OFF position, and then turn regulator counterclockwise to disconnect the regulator from cylinder, turn the cylinder locking bolt counterclockwise to loose the cylinder and remove the cylinder.
Troubleshooting PROBLEM POSSIBLE CAUSE CORRECTIVE MEASURES OBSERVED Gas odor Gas leak Check all gas connections Check gas supply pressure Low gas pressure Clean burner parts--see manual Delayed ignition Clogged or dirty burner ports "CLEANING AND MAINTENANCE" section Spent battery Change battery Incorrect burner Incorrect gas supply or pressure Check gas supply pressure...