Table of Contents
Advertisement
Quick Links
MOVING WATER FORWARD, SINCE 1968
VFX
DECORATIVE
AERATOR
2400, 3400, 4400
Operation &
Maintenance
Manual
3020379
ANSI/UL 778: 2016
Ed.6+R:22Feb2017
CSA C22.2 #108: 2014 Ed.5
Document number 884170
Document version 2021.2.1
800 Deere Rd. Prescott, WI 54021 | 715.262.4488 | sales@kascomarine.com | kascomarine.com
2400 - 4400 VFX AERATOR MANUAL
1
Advertisement
Table of Contents
Related Manuals for Kasco VFX
Summary of Contents for Kasco VFX
- Page 1 2400, 3400, 4400 Operation & Maintenance Manual 3020379 ANSI/UL 778: 2016 Ed.6+R:22Feb2017 CSA C22.2 #108: 2014 Ed.5 Document number 884170 Document version 2021.2.1 800 Deere Rd. Prescott, WI 54021 | 715.262.4488 | sales@kascomarine.com | kascomarine.com 2400 - 4400 VFX AERATOR MANUAL...
-
Page 2: Table Of Contents
Unit Specifications & Pattern Size ..................4 Parts Included .........................5 Unit Installation Instructions ....................7 Replacement Parts .........................8 Maintenance Recommendations ..................9 Troubleshooting Tips ......................10 Warranty ..........................11 Non-Warranty Repairs ......................12 Repair Contact Form ......................13 QUESTIONS? 715.262.4488 kascomarine.com | sales@kascomarine.com 2400 - 4400 VFX AERATOR MANUAL... -
Page 3: Safety First
• Kasco Aerating Fountains are intended for use with a Listed control panel having a GFCI protected receptacle, or field wiring terminals and disconnect switch, or a timer with a disconnect for use with a GFCI receptacle. Control panels MUST be installed by a qualified electrician. Ground Fault Circuit Interrupters (GFCIs) should be tested upon each installation and every month thereafter to ensure proper operation. -
Page 4: General Instructions
360 degrees around the unit and from below the unit. The water is pulled upward and thrust through the flotation collar into the air. Your Kasco Marine aerator is ready for immediate use (after installation). Make sure to keep the motor housing clean from hard water deposits and/or algae. (See Maintenance Recommendations.) It is extremely important that proper and sufficient voltage is supplied to... -
Page 5: Unit Specifications & Pattern Size
Hardwire C-85 / Plug into or 4400HVFX 8 ft. 26 ft. 208-240 hardwire C-85 TOOLS AND SUPPLIES NEEDED • 7/16” socket and ratchet • 7/16” wrench • 11/32” wrench (for #8 fasteners) 7/16’’ socket 7/16’’ combination wrench 11/32” wrench 2400 - 4400 VFX AERATOR MANUAL... -
Page 6: Parts Included
475630 Bottom screen section 361540 1/4”-20 nut 840536 #8 nut 771034 #8 flat washer 361543 #8 lock washer 771033 #8 x 3/4” screw 361545 Mooring ropes (not pictured) 990700 Cable ties (not pictured) 415038 2400 - 4400 VFX AERATOR MANUAL... - Page 7 Bring bottom screen sections together. 4. Tighten down in 6 places to hold the screen together. 5. Secure the bottom screen to the float in 3 places. Make sure cord is sticking out of notch. 2400 - 4400 VFX AERATOR MANUAL...
-
Page 8: Unit Installation Instructions
If your Kasco cord comes with a strain relief kit at- tached, attach the available link to the float-side knot in the mooring rope, as pictured here. -
Page 9: Replacement Parts
O-ring 990281 Sealing plug 990280 Zinc, assembly 243475 1/2”-20 x 3/4” long hex head bolt 243405 Washer, 1/2” bronze internal 241024 tooth lock Debris flinger, .500 diameter shaft 1 990410 1/2”-20 jam nut 342058 2400 - 4400 VFX AERATOR MANUAL... -
Page 10: Maintenance Recommendations
SACRIFICIAL ANODE: A sacrificial anode is supplied on the shaft of all VFX Model aerators for protection from corrosion and electrolysis. The anode should be updated/replaced if reduced to half the original size or if white in color. -
Page 11: Troubleshooting Tips
“My Aerator turns itself off and back on without the timer and without tripping the GFCI breaker.” (single phase units only) Each Kasco aerator has a Thermal Overload built in that will turn the unit off when it overheats. Once the unit has cooled down, it will start back up. If you are noticing these symptoms, the unit should be unplugged immediately because the Thermal Overload will continue to turn on and off until it burns out and damages the motor. -
Page 12: Warranty
(excluding ropes, power cord, and propeller). The Kasco Marine, Inc. obligation under this warranty is limited to replacing or repairing free of charge any defective part within the warranty period from the date of shipment. Customer shall pay shipping charges for returning the unit to Kasco or an Autho- rized Repair Center. -
Page 13: Non-Warranty Repairs
Please ship according to the instructions on the previous provided. Kasco Marine does estimates on repairs at the request of the customer. The request for estimate should be included in the letter that accompanies the returned unit and must include a daytime phone number and/ or e-mail address. -
Page 14: Repair Contact Form
Back to Contents REPAIR CONTACT FORM • Kasco requires that all equipment sent for repair MUST be accompanied by this form and marked to Repairs attention. Kasco Marine • Unit should be cleaned before shipping. 800 Deere Road • Kasco is NOT responsible for shipping damage accrued in Prescott, WI 54021 return shipment.