Related Manuals for W Audio MIC65
Summary of Contents for W Audio MIC65
- Page 1 RM 30 UHF Handheld Radio Microphone System User Manual Order codes: MIC64 - 863.1Mhz MIC65 - 864.8Mhz...
-
Page 2: Safety Advice
Safety advice Safety advice WARNING FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START-UP! • Before your initial start-up, please make sure that there is no damage caused during transportation. • Should there be any damage, consult your dealer and do not use the equipment. • To maintain the equipment in good working condition and to ensure safe operation, it is necessary for the user to follow the safety instructions and warning notes written in this manual. • Please note that damages caused by user modifications to this equipment are not subject to warranty. CAUTION! CAUTION! KEEP THIS EQUIPMENT TAKE CARE USING AWAY FROM MOISTURE, THIS EQUIPMENT! RAIN AND LIQUIDS, AND HIGH VOLTAGE-RISK OUT OF DAMP/HUMID... - Page 3 Operating frequency 863.1Mhz 864.8Mhz 1 x receiver, 1 x audio lead, Power supply DC 12-15V, 500mA (adaptor supplied) 1 x wireless microphone, System in case dimensions 310 x 430 x 100mm 1 x PSU, 1 x carry case System in case weight 1.7kg & 1 x user manual Order code MIC64 MIC65 www.prolight.co.uk RM 30 User Manual...
- Page 4 Operating instructions Receiver panel identification: 1. Display: The receiver features a backlit display allowing the user to see the preset RF frequency. 2. RF Signal Indicator: The LED RF Signal indicator will illuminate amber when the receiver unit receives a valid RF radio signal. 3. Audio Peak Indicator: The LED Audio indicator will illuminate green to show when the audio signal received by the receiver. 4. Power Indicator: The LED power indicator will illuminate red when the receiver is powered on. 5. Volume Control: The receivers output volume is adjustable. Turn the level control anti clockwise to the lowest setting, or turn clockwise to adjust to the highest setting. 6. Antenna: The antenna receives the RF radio signal from the transmitter unit. For optimum reception, orientate vertically. Reception maybe impaired by obstacles between the transmitter and receiver. High power electrical equipment can cause unwanted interference. 7. DC Power Input: The receiver is powered by a standard DC power input 9-15V DC, 300mA regulated voltage supply. 8. Audio Output: 6.35mm (1/4”) jack socket outputting an unbalanced, 400mV line level audio output.
-
Page 5: Operation
Operating instructions Handheld transmitter Operation: identification: • Carefully, lift the antenna into the vertical position. 1. Grille • Connect the included power supply to a suitable 240V AC~50Hz 2. Display mains voltage outlet and plug the DC connector into the DC Power 3. Battery cover Input on the rear panel of the receiver (9-15V DC, 300mA 4. Power indicator minimum). on base • Using the supplied audio cable, connect the Audio Out on the rear 5. Power switch panel of the receiver to the mixer’s audio line input. on base • Switch on the power to the receiver, checking the red power LED illuminates. • Open the battery compartment on the transmitter (Optional Beltpack – slide downwards away from the belt clip. Handheld - unscrew the lower portion). Install the appropriate batteries into the transmitter, taking care to observe the orientation and polarity. Only use high quality, alkaline type batteries. Refit the battery compartment cover carefully. • Switch on the transmitter, during switch on the battery light on the transmitter illuminate. If the light does illuminate or glows dimly, the battery will require replacement. • Adjust the volume on the front panel of the receiver and if required also adjust the volume on the belt pack. NOTE: The RM 30 system is shipped with one handheld transmitter, an additional belt pack kit maybe purchased if required. The receiver in this system may... -
Page 6: Optional Accessories
Optional accessories Optional RM 30BP UHF Beltpack Add On Kits Add-on package suitable for use with the RM 30 and RM 30T UHF microphone systems. The RM 30BP Belt Pack Kit comes Specifications RM 30BP UHF Beltpack Add On KIts supplied with a belt pack transmitter, headset microphone and Operating frequency 863.1Mhz 864.8Mhz lavalier microphone which allow the user to interchange one or Battery type 2 x 1.5V AA (not supplied) more of the handheld microphones from the RM 30 and RM Order code MIC67 MIC68 30T systems, thus increasing the flexibility of the system. Beltpack transmitter identification: 1. Audio input connector 2. Volume knob 3. Transmitting antenna 4. Power switch 5. LED display 6. Low power indicator 7. Battery house 8. Belt clip... -
Page 7: Weee Notice
WEEE notice Correct Disposal of this Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed of with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal. www.prolight.co.uk RM 30 User Manual... - Page 8 www.prolight.co.uk RM 30 User Manual...