Annovi Reverberi AR 252 Instruction Manual

650 rpm - semi-hydraulic two diaphragm pump
Hide thumbs Also See for AR 252:

Advertisement

140° F - Max Water Temp
3/4" - Suction
3/8" Hose Barb- Outlet
AR252 - 650
RPm
m
odeL
AR252-SP/SGC
AR252-SP/A5/8
AR252-GR-GCI5/8
AR252-GR-GCI3/4
AR252-GR/A5/8-GCI
GCI - Pump with a
mounted control unit.
d
K
iAPHRAgm
iTS
m
d
odeL
eScRiPTion
AR43281
BlueFlex
AR43278
NBR
AR43279
Desmopan
INSTRUCTION MANUAL
- S
-H
emi
ydRAuLic
m
gPm m
Ax
6.5
6.5
6.5
6.5
6.5
V
V
K
K
ALVe
ALVe
iTS
iTS
m
m
d
d
odeL
odeL
eScRiPTion
eScRiPTion
AR2408
AR2408
Valves
Valves
T
d
wo
iAPHRAgm
L/m
m
PSi
Ax
in
Ax
24.6
362
24.6
362
24.6
362
24.6
362
24.6
362
o-R
K
ing
iTS
m
d
odeL
eScRiPTion
AR2409
O-Rings
AR 252
P
umP
m
B
HP P
Ax
AR
oweR
25
1.42
25
1.42
25
1.42
25
1.42
25
1.42
o
iL
m
odeL
AR64532D
AR64532D-C Case (6)Oil
w
eigHT
L
.
BS
8.8
8.8
8.8
14
14
d
eScRiPTion
Oil

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AR 252 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Annovi Reverberi AR 252

  • Page 1 AR 252 140° F - Max Water Temp 3/4” - Suction 3/8” Hose Barb- Outlet INSTRUCTION MANUAL AR252 - 650 ydRAuLic iAPHRAgm eigHT gPm m HP P odeL oweR AR252-SP/SGC 24.6 1.42 AR252-SP/A5/8 24.6 1.42 AR252-GR-GCI5/8 24.6 1.42 AR252-GR-GCI3/4 24.6 1.42...
  • Page 2 AR252 Pump...
  • Page 3 AR252 Control Unit Pressure Adjustment Knob AR1990 Control Unit for the AR252 Pumps. Optional Gauge Bypass Hose Barb Red Pressure Outlet Hose Barb Startup Release AR252 Control Unit Operation Instructions Full Bypass Startup Selection Spraying Operation Before Starting the Pump, Rotate Red Knob so the A is in the rotate the red knob so that the 12 o'clock position.
  • Page 4: Important Safety Information

    IMPORTANT SAFETY INFORMATION Intended uses The pump is designed and constructed for incorporation in plants and machinery (spraying machines for the protective treatment of agricultural crops and garden plants). All other uses constitute misuse unless ap- proved by the manufacturer's technical service The pump must be used in a manner appropriate to its technical data (see “Technical Data”), and must not be modified or improperly used.
  • Page 5 Installation diagram (guideline) The following is a simplified illustration of the typical installation layout and is purely guideline. Control Unit by-pass Tank Agitation Control Unit Intake filter Pump Delivery line filter...
  • Page 6: Installation Instructions

    INSTALLATION INSTRUCTIONS General guidelines on water supply connection To operate correctly, the diaphragm pump must draw in liquids from containers at atmospheric pressure. Do not supply the pump with pressurised liquids. For continuous duty, the pump should not draw in water by gravity from containers with liquid level at heights above 3 m.
  • Page 7 Safety recommendations for handling and lifting Before starting the operations, organise the intended working area so that the materials can be lifted and handled in safety. Unloading, loading, handling and lifting operations must be carried out by skilled, authorised, specifi­ cally trained staff.
  • Page 8 Installation • The crankshaft may turn in either direction. • The water connection with the pump must be made using hoses of suitable diameter, in all case no less than that of the pump fittings, securing them to the fittings using good quality clamps. The intake hose must be coil-reinforced to prevent restrictions.
  • Page 9 Safety recommendations for use Before start-up, the operator must perform the necessary safety checks. In the event of leaks from the pressurized pipes, stop the pump at once and fix the leak. Do not operate the pump above the limits set by the manufacturer to increase its performance. Preliminary checks If the pump has a pressure accumulator, check its level of inflation, see "Checking the inflation pressure".
  • Page 10 Safety recommendations for maintenance Before doing any maintenance work, depressurise the water system and isolate the pump from all en- ergy sources. When the jobs are done, before restarting the pump, check that no tools, rags or other materials have been left close to moving parts or in hazardous zones.
  • Page 11: Maintenance Instructions

    MAINTENANCE INSTRUCTIONS Table of lubricants The pump is delivered complete with high-performance 30 weight, non-detergent oil suitable for the intended ambient conditions (see "Environmental operating limits"). Inspecting the pump mounting Check that the pump's fixing screws have not become loose. If necessary, tighten them with the driving torque stated in the installation design.
  • Page 12 MAINTENANCE INSTRUCTIONS Checking the inflation pressure Check level of inflation, with the pump shutoff using an air chuck fitted with a pressure gauge. The accumulator is inflated by the manufacturer for use of the pump at its maximum pressure. For adaptation of the accumulator pressure to the working pressure, refer to the table below.
  • Page 13 Pump Storage It is important to comply with the recommendations for storage in the operator's manual of the machine into which the pump is incorporated. For the pump itself, at the end of pumping operations it is essential to flush out the pump by pumping clean water.
  • Page 14: Troubleshooting

    TROUBLESHOOTING The information provided is intended to provide guidance how to deal with malfunctions which may occur during use. Some of these procedures may be carried out by skilled staff, while others have to be performed at specialised service centres since they require the use of specific equipment as well as detailed knowledge of repair opera­ tions.
  • Page 15 TROUBLESHOOTING Remedy Problem Cause Oil seal on pump Replace the worn oil seal. shaft worn. Oil on pump body or base. Oil pressure inside pump too high. Restore correct oil level in tank. Pump using too much oil (oil flowing from delivery port) or oil Stop the pump at once.
  • Page 16 A.R. NORTH AMERICA A.R. NORTH AMERICA AR 252 67 65 48 - 1 48 - 2 37 104 Versions GR Version A5/8 48 - 3 48 - 4 S.G.C. V.R.I. 49 48 39 48 40 41 42 48 - 5...
  • Page 17 3/4" 800082 Diaphragm BlueFlex 801230 Pinion Z=13 5/8" 802050 Sleeve AR 252 800820 Body 802051 Sleeve AR 252 (Viton) 800800 Bolt TCEI M8x16 740290 O-ring Ø 14x1.78 550460 Elbow 3/4" 801960 Oil sight glass 800692 Flange 800520 Ring nut 880280 Bolt...
  • Page 18: Overall Dimensions

    SP SGC AP SP SGC Ø 8.5 Ø 1/2" G Ø 1/2" G SP SGC Ø 8.5 AP SP SGC AR 252 SP VRI GR30 4,75 Ø 1/2" G Ø 1/2" G Ø 18 4,75 Ø 18 CR/xS Ø 8.5 AP SP SGC R17.5...

This manual is also suitable for:

Ar252 sp/sgcAr252-sp/a5/8Ar252-gr-gci5/8Ar252-gr-gci3/4Ar252-gr/a5/8-gciAr252-gr

Table of Contents

Save PDF