Advertisement
Available languages
Available languages
TECHNICAL DATA
CORDLESS PERCUSSION DRILL/DRIVER
Production code....................................................................................................................
Drilling capacity in steel ............................................................................
Drilling capacity in wood ...........................................................................
Wood screws (without pre-drilling) ...........................................................
Drilling capacity in brick and tile ...............................................................
No-load speed 1st gear ............................................................................
No-load speed 2nd gear ...........................................................................
Torque ......................................................................................................
Battery voltage..........................................................................................
Drill chuck range .......................................................................................
Weight according EPTA-Procedure 01/2014 (1.5 Ah) ..............................
Weight according EPTA-Procedure 01/2014 (2.0 Ah) ..............................
Recommended ambient operating temperature .......................................
Recommended battery types....................................................................
Recommended charger ............................................................................
Noise/vibration information
Measured values determined according to EN 62841.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A)) .........................................
Sound power level (Uncertainty K=3dB(A)) ..............................................
Wear ear protectors!
Total vibration values (vector sum in the three axes) determined according to EN 62841.
Vibration emission value
Impact drilling into concrete a
...........................................................
h.ID
Uncertainty K= ......................................................................................
Drilling into metal a
............................................................................
h.D
Uncertainty K= ......................................................................................
Screwing a
...........................................................................................
h
Uncertainty K= ......................................................................................
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 62841 and may be used to compare one tool with
another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for diff erent applications, with diff erent accessories or poorly maintained, the
vibration emission may diff er. This may signifi cantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running but not actually doing the job. This may
signifi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the eff ects of vibration such as: maintain the tool and the accessories, keep the hands warm, organisation of work
patterns.
WARNING Read all safety warnings, instructions, illustrations and
specifi cations provided with this power tool. Failure to follow all instructions listed
below may result in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
DRILL SAFETY WARNINGS
Safety instructions for all operations
Hold the power tool by insulated gripping surfaces, when performing an operation
where the cutting accessory or fasteners may contact hidden wiring.
Cutting accessory or fasteners contacting a "live" wire may make exposed metal parts of
the power tool "live" and could give the operator an electric shock.
Wear ear protectors when impact drilling. Exposure to noise can cause hearing loss.
Safety instructions when using long drill bits
Never operate at higher speed than the maximum speed rated of the drill bit. At
higher speeds, the bit is likely to bend if allowed to rotate freely without contacting the
workpiece, resulting the personal injury.
Always start drilling at low speed and with the bit tip in contact with the
workpiece. At higher speeds, the bit is likely to bend if allowed to rotate freely without
contacting the workpiece, resulting the personal injury.
Apply pressure only in direct line with the bit and do not apply excessive
pressure. Bits can bend causing breakage or loss of control, resulting in personal injury.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses when working with the machine.
The use of protective clothing is recommended, such as dust mask, protective gloves,
sturdy non-slip footwear, helmet and ear defenders.
The dust produced when using this tool may be harmful to health. Do not inhale the dust.
Wear a suitable dust protection mask.
Do not machine any materials that present a danger to health (e.g. asbestos).
16
ENGLISH
BSB12 G3
BSB14 G3
..... 4566 14 04... .............4566 20 04...
...000001-999999
...000001-999999
..............10 mm .................. 13 mm
..............30 mm .................. 32 mm
................5 mm .................... 5 mm
..............10 mm .................. 10 mm
............350 min
-1
.............. 400 min
-1
..........1500 min
-1
............ 1700 min
-1
..............32 Nm .................. 36 Nm
..............12 V .................. 14,4 V
....... 0,8-10 mm ............ 2,0-13 mm
.............1,1 kg ................... 1,2 kg
.............1,2 kg ................... 1,3 kg
........................+5...+40 °C
.. L1215G3, L1220G3, L1415G3, L1420G3
.........................AL1214G3
...........84,5 dB (A) .......... 86,5 dB (A)
...........95,5 dB (A) .......... 97,5 dB (A)
.............9,3 m/s
2
................ 9,4 m/s
2
.............1,5 m/s
2
................ 1,5 m/s
2
.............0,7 m/s
2
................ 2,0 m/s
2
.............1,5 m/s
................ 1,5 m/s
2
2
.............0,5 m/s
................ 1,2 m/s
2
2
.............1,5 m/s
................ 1,5 m/s
2
22
Switch the device off immediately if the insertion tool stalls! Do not switch the device on
again while the insertion tool is stalled, as doing so could trigger a sudden recoil with a
high reactive force. Determine why the insertion tool stalled and rectify this, paying heed
to the safety instructions.
The possible causes may be:
• it is tilted in the workpiece to be machined
• it has pierced through the material to be machined
• the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool may become hot during use.
WARNING! Danger of burns
• when changing tools
• when setting the device down
Chips and splinters must not be removed while the machine is running.
When working in walls ceiling, or fl oor, take care to avoid electric cables and gas or
waterpipes.
Clamp your workpiece with a clamping device. Unclamped workpieces can cause severe
injury and damage.
Remove the battery pack before starting any work on the machine.
Do not dispose of used battery packs in the household refuse or by burning them. AEG
Distributors off er to retrieve old batteries to protect our environment.
Do not store the battery pack together with metal objects (short circuit risk).
Use only AL1214G3 chargers for charging System L1215G3, L1220G3, L1415G3 and
L1420G3 battery packs. Do not use battery packs from other systems.
Never break open battery packs and chargers and store only in dry rooms. Keep dry at
all times.
Battery acid may leak from damaged batteries under extreme load or extreme
temperatures. In case of contact with battery acid wash it off immediately with soap and
water. In case of eye contact rinse thoroughly for at least 10 minutes and immediately
seek medical attention.
Warning! To reduce the risk of fi re, personal injury, and product damage due to a short
circuit, never immerse your tool, battery pack or charger in fl uid or allow a fl uid to fl ow
inside them. Corrosive or conductive fl uids, such as seawater, certain industrial
chemicals, and bleach or bleach containing products, etc., can cause a short circuit.
SPECIFIED CONDITIONS OF USE
The battery percussion drill/screwdriver may be used for drilling, percussion drilling, as
well as screwdriving for independent use away from mains supply.
Do not use this product in any other way as stated for normal use.
EC-DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole responsibility that the product described
under "Technical Data" fulfi lls all the relevant regulations and the directives 2011/65/EU
(RoHS), 2014/30/EU, 2006/42/EC, and the following harmonized standards have been
used:
EN 62841-1:2015
EN 62841-2-1:2018+A11:2019
EN 55014-1:2017+A11:2020
EN 55014-2:2015
EN IEC 63000:2018
Winnenden, 2020-11-23
Alexander Krug
Managing Director
Authorized to compile the technical fi le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
GB-DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole responsibility that the product described
under "Technical Data" fulfi lls all the relevant provisions of the following Regulations S.I.
2008/1597 (as amended), S.I. 2016/1091 (as amended), S.I. 2012/3032 (as amended)
and that the following designated standards have been used:
BS EN 62841-1:2015
BS EN 62841-2-1:2018+A11:2019
BS EN 55014-1:2017+A11:2020
BS EN 55014-2:2015
BS EN IEC 63000:2018
Winnenden, 2020-11-23
Alexander Krug
Managing Director
Authorized to compile the technical fi le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
BATTERIES
Battery packs which have not been used for some time should be recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance of the battery pack.
Avoid extended exposure to heat or sunshine (risk of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, the battery packs have to be fully charged, after used.
To obtain the longest possible battery life remove the battery pack from the charger once
it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C and away from moisture
Store the battery packs in a 30% - 50% charged condition
Every six months of storage, charge the pack as normal.
BATTERY PACK PROTECTION LI-ION BATTERY
The battery pack has overload protection that protects it from being overloaded and
helps to ensure long life.
Under extreme stress the battery electronics switch off the machine automatically. To
restart, switch the machine off and then on again. If the machine does not start up again,
the battery pack may have discharged completely. In this case it must be recharged in
the battery charger.
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods Legislation requirements.
Transportation of those batteries has to be done in accordance with local, national and
international provisions and regulations.
• The user can transport the batteries by road without further requirements.
• Commercial transport of Lithium-Ion batteries by third parties is subject to Dangerous
Goods regulations. Transport preparation and transport are exclusively to be carried
out by appropriately trained persons and the process has to be accompanied by
corresponding experts.
When transporting batteries:
• Ensure that battery contact terminals are protected and insulated to prevent short
circuit.
• Ensure that battery pack is secured against movement within packaging.
• Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice
MAINTENANCE
Use only AEG accessories and spare parts. Should components need to be replaced
which have not been described, please contact one of our AEG service agents (see our
list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please state the machine type
printed as well as the six-digit No. on the label and order the drawing at your local
service agents or directly at: Techtronic Industries GmbH, Max-Eyth-Straße 10,
71364 Winnenden, Germany.
SYMBOLS
CAUTION! WARNING! DANGER!
Remove the battery pack before starting any work on the machine.
Please read the instructions carefully before starting the machine.
Do not dispose electric tools, batteries/rechargeable batteries together
with household waste material.
Electric tools and batteries that have reached the end of their life must
be collected separately and returned to an environmentally compatible
recycling facility.
Check with your local authority or retailer for recycling advice and
collection point.
n
No-load speed
0
V
Volts
Direct current
European Conformity Mark
British Confomity Mark
Ukraine Conformity Mark
EurAsian Conformity Mark
ENGLISH
17
Advertisement
