Using Your Steam Pocket Mop; Intelligent Steam Control - Shark KLIK N' FLIP SMARTRONIC DELUXE Owner's Manual

Using Your Steam Pocket Mop
®
IMPORTANT: Make sure you do not use the Steam Mop without attaching a Dirt Grip
the water tank first. When you are using the Steam Mop for the first time, it might take longer than the normal
30 seconds to start steaming.
IMPORTANT: Do not use on unsealed wood or unglazed ceramic floors. On surfaces that have been treated with
wax and on some no-wax floors, the sheen may be removed by the heat and steam action. Test an isolated area
of the surface to be cleaned before proceeding. Check the use and care instructions from the floor manufacturer.
fig. 9 fig. 10
NOTE: To prolong the life of your Steam Mop, we
recommend using distilled water.
NOTE: Sweep or vacuum your floors prior to cleaning
with your Steam Mop.
1 Twist the Quick-Release Cord Holder to unwrap the
power cord completely. (fig. 9) Plug into an electrical
outlet.
2
When it's first plugged in, the unit will be in Standby
mode. The 3 lights below the Steam Control Button
will blink to indicate Standby mode.
3
To select the steam mode, press the Steam Control
Button once for LOW (1 blue light) twice for MED (2
blue lights) or three times for HI (3 blue lights).
4 Clean your floors with a forward and backward
motion.
5
When you need an extra burst of steam to clean
a stuck-on stain, you can use the Steam Blaster ™
feature. Flip the head over so that it is behind the
mop body, then tilt the mop handle down. This will
cause the the Steam Blaster (fig. 10) to emit a
concentrated blast of steam onto the stain.
CAUTION: While in Steam Blaster mode, do not
leave stationary for more than one minute.
CAUTION: Do not scrub any one area for an
extended period of time.
36
pad and adding water to
™
fig. 11a
fig. 11b
6 To stop the Steam Blaster spray, simply raise the
handle. You can then flip the mop head back into its
original position and continue cleaning.
7
When finished mopping, press the Steam Control
Button. The three blue lights will blink, indicating that
the unit is in Standby mode. Once in Standby mode,
unplug the unit.
8 To remove the Dirt Grip pad, simply lift the Steam
™
Mop straight up by the handle until the Klik n' Flip
Mop Head is hanging straight down. Press the
Release button on the back of the Steam Mop body
(fig 11a), and both sides of the head will drop open,
releasing the pad. (fig 11b)
9
Once the Dirt Grip pad has been released, close the
Klik n' Flip Mop Head. To close, gently press one side
of the Klik n' Flip Mop Head to the floor until that side
clicks into place. Repeat on the other side.
10 When the water tank is empty, the Steam Mop will
stop producing steam. You can refill the water tank
at any time as long as the Steam Mop is unplugged.
Follow the water tank filling instructions on page 35.
NOTE: Please wait 2 to 3 minutes for the Steam Mop
to cool off before switching the mop head. Never
leave the Steam Mop with a damp/wet Dirt Grip pad
on any floor for an extended period of time.

Intelligent Steam Control

®
The Shark Klik n' Flip Smartronic Deluxe Steam Pocket
®
you can use the right amount of steam for the cleaning task at hand. See below for tips on when to use each setting.
SETTING IDEAL FOR THESE SEALED
SURFACES
LOW
Laminate
Hardwood
Marble
MED
Hardwood
Marble
Tile
Stone
HI
Hardwood
Marble
Tile
Stone
For an extra burst of steam, you can use the Steam Blaster feature in LOW, MED and HI.
Steam Blaster ™
Follow the instructions found on the "Using your Steam Pocket
TO SANITIZE* WITH THE STEAM MOP USING THE KLIK N' FLIP MOP HEAD AND THE DIRT GRIP
1
Attach a clean Dirt Grip pad to the Klik N' Flip Mop Head.
2 Plug in the unit and press the Steam Control Button to select the HI Setting.
3 Wait 30 seconds for the unit to begin producing steam.
4
Start mopping on an appropriate sealed hard-floor surface with a forward and backward motion. After three minutes,
your unit is ready to be used to sanitize.
5 Using a forward and backward motion, move the unit over the area you seek to sanitize. Repeat at least 3 times.
* Sanitization studies were conducted under controlled test conditions. Household conditions and results may vary.
With Klik n' Flip Mop in HI mode only when used with Steam Mop. Not in Steam Blaster mode.
Mop has 3 unique Intelligent Steam Control settings so
®
RECOMMENDED USAGE
Cleaning delicate surfaces
Light cleaning and dusting
Loosening and lifting light dirt
Cleaning sealed surfaces and large areas
Basic, everyday cleaning
Removing spots and smaller messes
Cleaning moderate and heavy traffic areas
Deep cleaning and cleaning hard-to-clean surfaces
Tough cleaning and removing stuck-on messes and stains
Deep cleaning heavy traffic areas
Cutting through heavy dirt and grime
® Mop" page.
PAD:
™
www.sharkclean.eu 37