Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for IFM CR710S
Summary of Contents for IFM CR710S
- Page 1 Installation instructions ecomatController CR710S CR711S P_MZ_e100_0094...
-
Page 2: Table Of Contents
7�1 CR710S � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �... - Page 3 CR710S/CR711S 7�1�5 Connectors� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 29 7�1�6 Connector A / wiring �...
-
Page 4: Preliminary Note
CR710S/CR711S 1 Preliminary note This document applies to devices of the type "ecomatController" (art� no�: CR710S/CR711S)� It is part of the device� This document is intended for specialists� These specialists are people who are qualified by their appropriate training and their experience to see risks and to avoid possible hazards that may be caused during operation or maintenance of the device�... -
Page 5: Safety Instructions
The connection terminals may only be supplied with the signals indicated in the technical data and/or on the device label and only the approved accessories from ifm electronic gmbh may be connected� 2.4 Housing temperature As described in the technical specifications below the device can be operated in a wide ambient temperature range�... -
Page 6: 2�5 Tampering With The Device
CR710S/CR711S 2.5 Tampering with the device In case of malfunctions or uncertainties please contact the manufacturer� Any tampering with the device can seriously affect the safety of operators and machinery� This is not permitted and leads to the exclusion of any liability and warranty claims�... -
Page 7: Installation
CR710S/CR711S 4 Installation 4.1 Fastening P_MZ_e100_0093 Original S Scale: 1:2 ► Fix the controller to a flat surface using 4 galvanized M6 screws� Tightening torque: 10 ±2 68,4 Total height with the attached Installation connector� NOTE To avoid contact corrosion between the mounting screws and the module EPS Sour housing, do not use any stainless steel screws or nickel-plated screws�... -
Page 8: 4�2 Installation Position
CR710S/CR711S 4.2 Installation position In wet environments, install the controller ensuring that no liquid remains on the connectors� 4.3 Mounting surface NOTE The housing must not be exposed to any torsional forces or mechanical stress� ► Use compensating elements if there is no flat mounting surface available�... -
Page 9: Electrical Connection
CR710S/CR711S 5 Electrical connection 5.1 Wiring Wiring (→ 7 Technical data) Only connect the connector pins as shown in the pin layout� Unspecified connector pins remain unconnected� P_MZ_e100_0094 Original Scale Drawing (MTD) ► Connect all indicated supply cables and GND terminals�... -
Page 10: 5�3 Fuses
CR710S/CR711S To ensure the protection of the device against electrical interference and the safe function of the device, the housing must be connected to the ground / body of the vehicle in the shortest possible way� ► Connect the device to the ground of the vehicle using the M4 self-tapping screw (included)�... -
Page 11: 5�4�1 Gnd Connections
CR710S/CR711S ► Basically all supply and signal cables must be laid separately� ► Connect supply and ground cables to the controller and the sensors/actuators via the respective common star point� If a prewired connection cable is used, remove the cores with unused signal inputs and outputs�... -
Page 12: 5�5 Analogue Inputs
CR710S/CR711S 5.5 Analogue inputs supply input input nn GND controller Shield Connection of the analogue inputs (A) ► Connect GND to the GND of the signal source� Do not connect GND to other GND connectors or to the GND star point�... -
Page 13: 5�6 Resistor Inputs
CR710S/CR711S 5.6 Resistor inputs supply input input nn GND controller Shield Connection of the resistor inputs (R) ► Connect GND to the GND of the signal source� Do not connect GND to other GND connectors or to the GND star point�... -
Page 14: 5�7 High Side Digital Inputs (Cso)
CR710S/CR711S 5.7 High side digital inputs (CSO) supply input , FRQ input , FRQ nn GND controller Shield Connection of the high side inputs (B , FRQ 1: Connection for 3-wire sensors ► Connect the GND of the signal source with the common GND star point�Do not... -
Page 15: 5�8 Analogue Outputs
CR710S/CR711S 5.8 Analogue outputs supply Con. A A (0...10 V) load Con. A controller Shield Connection of the analogue outputs (A) ► Connect the GND of the load to GND � Do not connect the GND of the load to other GND connections or to the... -
Page 16: 5�9 Low Side Digital Outputs (Csi) / H-Bridge
CR710S/CR711S 5.9 Low side digital outputs (CSI) / H-bridge supply load load load controller load Shield Connection of the low side digital outputs (PWM ► Supply low-side outputs (B ) via a high side output (B ) of the same output group�... -
Page 17: 5�10 Mixed Operation (12 V / 24 V)
CR710S/CR711S 5.10 Mixed operation (12 V / 24 V) supply 24 V sensor input output load sensor input output load sensor input output load controller Shield Example connection to 24 V and 12 V power supply combined The operation of the output groups is possible with different supply voltages�... -
Page 18: Set-Up
6.3 Getting started ► Check if the pre-installed, latest version of the ifm operating system is required� If necessary, download and install a different version via TFTP� ► Connect the device to the notebook/PC via the Ethernet interface�... -
Page 19: 6�4 Required Documentation
● Programming manual CODESYS V3�5 (alternatively as online help) The manuals can be downloaded from the internet: www.ifm.com → Search → Art. no. → Documents & downloads CODESYS online help: www.ifm.com → Service → Download → Control systems* *) Download area with registration... -
Page 20: Technical Data
Current consumption VBB max� 600 mA at 12 V max� 400 mA at 24 V ifm electronic gmbh ● Friedrichstraße 1 ● 45128 Essen We reserve the right to make technical alterations without prior notice! CR710S / page 1 22� Nov� 2017... - Page 21 2 x LED (G) for ETH0 and ETH1 Application LED 4 x three-colour LED (R/G/B) for APP0, APP1, APP2 and APP3 ifm electronic gmbh ● Friedrichstraße 1 ● 45128 Essen We reserve the right to make technical alterations without prior notice! CR710S / page 2...
- Page 22 APP3 mable blue status display of the application, freely program- mable ifm electronic gmbh ● Friedrichstraße 1 ● 45128 Essen We reserve the right to make technical alterations without prior notice! CR710S / page 3 22� Nov� 2017...
-
Page 23: 7�1�2 Test Standards And Regulations
10���500 Hz; 0�72 mm/10 g; 10 cycles/axis ISO 16750-3 Bump 30 g/6 ms; 24,000 shocks * in preparation ifm electronic gmbh ● Friedrichstraße 1 ● 45128 Essen We reserve the right to make technical alterations without prior notice! CR710S / page 4 22� Nov� 2017... -
Page 24: 7�1�3 Connector A / Input Characteristics
Switch-on level > 0�7 VBB Switch-off level < 0�3 VBB Accuracy ± 10 µs ifm electronic gmbh ● Friedrichstraße 1 ● 45128 Essen We reserve the right to make technical alterations without prior notice! CR710S / page 5 22� Nov� 2017... - Page 25 ● Friedrichstraße 1 ● 45128 Essen We reserve the right to make technical alterations without prior notice! CR710S / page 6 22� Nov� 2017...
-
Page 26: 7�1�4 Connector A / Output Characteristics
Digital output (B Range diagnostics min - max� 0 A / 2�5 A (default) ifm electronic gmbh ● Friedrichstraße 1 ● 45128 Essen We reserve the right to make technical alterations without prior notice! CR710S / page 7 22� Nov� 2017... - Page 27 ± 5 % FS Output groups VBB Load current per output group ≤ 12 A ifm electronic gmbh ● Friedrichstraße 1 ● 45128 Essen We reserve the right to make technical alterations without prior notice! CR710S / page 8 22� Nov� 2017...
- Page 28 (CSI) pulse-width modulation current-controlled supply output group via semiconductor switch supply sensors/module ifm electronic gmbh ● Friedrichstraße 1 ● 45128 Essen We reserve the right to make technical alterations without prior notice! CR710S / page 9 22� Nov� 2017...
- Page 29 1-81: see wiring connector A EPS Source Product Scale D Frame Size: 80 ifm electronic gmbh ● Friedrichstraße 1 ● 45128 Essen We reserve the right to make technical alterations without prior notice! CR710S / page 10 22� Nov� 2017...
-
Page 30: 7�2�6 Connector A / Wiring
● Friedrichstraße 1 ● 45128 Essen We reserve the right to make technical alterations without prior notice! CR710S / page 11 22� Nov� 2017... - Page 31 Current consumption VBB max� 600 mA at 12 V max� 400 mA at 24 V ifm electronic gmbh ● Friedrichstraße 1 ● 45128 Essen We reserve the right to make technical alterations without prior notice! CR711S / page 1 22 Nov� 2017...
- Page 32 2 x LED (G) for ETH0 and ETH1 Application LED 4 x three-colour LED (R/G/B) for APP0, APP1, APP2 and APP3 ifm electronic gmbh ● Friedrichstraße 1 ● 45128 Essen We reserve the right to make technical alterations without prior notice! CR711S / page 2...
- Page 33 APP3 mable blue status display of the application, freely program- mable ifm electronic gmbh ● Friedrichstraße 1 ● 45128 Essen We reserve the right to make technical alterations without prior notice! CR711S / page 3 22 Nov� 2017...
- Page 34 10���500 Hz; 0�72 mm/10 g; 10 cycles/axis ISO 16750-3 Bump 30 g/6 ms; 24,000 shocks * in preparation ifm electronic gmbh ● Friedrichstraße 1 ● 45128 Essen We reserve the right to make technical alterations without prior notice! CR711S / page 4 22 Nov� 2017...
- Page 35 Switch-on level > 0�7 VBB Switch-off level < 0�3 VBB Accuracy ± 10 µs ifm electronic gmbh ● Friedrichstraße 1 ● 45128 Essen We reserve the right to make technical alterations without prior notice! CR711S / page 5 22 Nov� 2017...
- Page 36 (default) Observe the notes on the confi guration of the inputs/outputs! (Programming manual "ecomatController CR711S") ifm electronic gmbh ● Friedrichstraße 1 ● 45128 Essen We reserve the right to make technical alterations without prior notice! CR711S / page 6 22 Nov� 2017...
- Page 37 0���2 supply sensors/module ifm electronic gmbh ● Friedrichstraße 1 ● 45128 Essen We reserve the right to make technical alterations without prior notice! CR711S / page 7 22 Nov� 2017...
- Page 38 Digital output (B Range diagnostics min - max� 0 A / 4 A (default) ifm electronic gmbh ● Friedrichstraße 1 ● 45128 Essen We reserve the right to make technical alterations without prior notice! CR711S / page 8 22 Nov� 2017...
- Page 39 ± 1�5 % FS (for inductive loads) Range diagnostics min - max� 0 A / 2�5 A (default) ifm electronic gmbh ● Friedrichstraße 1 ● 45128 Essen We reserve the right to make technical alterations without prior notice! CR711S / page 9...
- Page 40 (CSI) pulse-width modulation current-controlled supply output group via semiconductor switch 0���2 supply sensors/module ifm electronic gmbh ● Friedrichstraße 1 ● 45128 Essen We reserve the right to make technical alterations without prior notice! CR711S / page 10 22 Nov� 2017...
- Page 41 1-81: see wiring connector A EPS Source Product Scale D Frame Size: 80 ifm electronic gmbh ● Friedrichstraße 1 ● 45128 Essen We reserve the right to make technical alterations without prior notice! CR711S / page 11 22 Nov� 2017...
- Page 42 0���2 supply sensors/module ifm electronic gmbh ● Friedrichstraße 1 ● 45128 Essen We reserve the right to make technical alterations without prior notice! CR711S / page 12 22 Nov� 2017...
-
Page 43: Maintenance, Repair And Disposal
CR710S/CR711S 8 Maintenance, repair and disposal The unit is maintenance-free� ► Do not open the housing as the device does not contain any components which can be maintained by the user� The device must only be repaired by the manufacturer�...
Need help?
Do you have a question about the CR710S and is the answer not in the manual?
Questions and answers