These factors must be supplied by the person(s) caring for and operating this equipment. ONLY YOU CAN PREVENT ACCIDENTS!! O:\Manuals\818 MANUAL\818 Manual P.W. rev (2) 09-2019.doc - 3 -...
SPECIFICATIONS & FEATURES The Model 818 is a single feed roll unit with an 18" x 18" infeed opening. Designed for mountains of brush and large branches, this chipper feeds up to a rate of 65' per minute, and is almost impossible to keep up with.. Live Hydraulics, 9,000 lb. Heavy Duty Jack, Dual 5,000 lb.
It has been and will continue to be the policy of SALSCO to update existing machines at its own discretion. Whenever possible, new designs will be made in such a way that they can be "Retro Fit" if so desired.
BRUSH CHIPPERS ANSI Z133.1-2006 American National Standard for Arboricultural Operations Safety Requirements O:\Manuals\818 MANUAL\818 Manual P.W. rev (2) 09-2019.doc - 6 -...
Page 7
BRUSH REMOVAL CHIPPING ANSI Z133.1-2006 American National Standard for Arboricultural Operations Safety Requirements O:\Manuals\818 MANUAL\818 Manual P.W. rev (2) 09-2019.doc - 7 -...
Page 8
Let the engine run a few minutes to cool down and then shut down. Chipper flywheel will still be rotating. NEVER PERFORM ANY SERVICE OR MAINTENANCE, OR REMOVE ANY GUARDS WHILE THE FLYWHEEL IS MOVING! O:\Manuals\818 MANUAL\818 Manual P.W. rev (2) 09-2019.doc - 8 -...
Page 9
KNOW YOUR FELLOW CO-WORKERS WHEREABOUTS AT ALL TIMES! • NEVER LET ANYONE OPERATE THIS MACHINE WITHOUT THE PROPER TRAINING! • REMEMBER, THIS MACHINE CAN CHIP UP A TELEPHONE POLE IN 1- MINUTE! O:\Manuals\818 MANUAL\818 Manual P.W. rev (2) 09-2019.doc - 9 -...
11. Reinstall top housing and discharge elbow. Be sure to use roll pin to keep housing aligned. 12. Install pulley. Be sure to use straight edge to line up pulley. O:\Manuals\818 MANUAL\818 Manual P.W. rev (2) 09-2019.doc - 10 -...
Page 11
This check should be made yearly to assure the maximum performance from your Salsco chipper. Please call with any questions on this or any other problems.
Page 13
Should you drop a nut, bolt or blade in the housing you must retrieve it before you start up the machine. HINT: Salsco recommends replacement of nuts, bolts and washers, when replacing or sharpening chipper blades. The locking ability of these parts may have been violated. HINT: It is strongly recommended to have a set of blades, bolts, nuts and washers, on the shelf, to prevent downtime while blades are being sharpened.
Page 15
Once the PTO is installed, follow this schedule below. Lubricating Schedule Bronze Release Bearings Daily Main Bearings Every 100 Hours PTO Cross Shaft Every 500 Hours Linkage and Levers Use SAE 30 Synthetic every 500 Hours O:\Manuals\818 MANUAL\818 Manual P.W. rev (2) 09-2019.doc - 15 -...
Below is a quick reference chart for various “Flat Head Cap Screws” and the torque recommendations. VALUES ARE STATED IN FOOT POUNDS BOLT SIZE Thds Per Inch SAE Grade 5 SAE Grade 8 ¼ 5/16 7/16 ½ 9/16 ¾ O:\Manuals\818 MANUAL\818 Manual P.W. rev (2) 09-2019.doc - 37 -...
Your Salsco Commercial or Turf Equipment product is a commercial type product and is normally manufactured and sold for commercial or industrial use. Salsco will, for the original purchaser, for one (1) year from the date of purchase (90 days if used for rental purposes) repair or replace, free of charge, any SALSCO part or parts found to be defective in material, workmanship or both.