Related Manuals for Wavecom TnT Titan
Summary of Contents for Wavecom TnT Titan
- Page 1 Wavecom TnT Titan Portable Appliance Tester User Manual + Certificate of Warranty and Product Support Information...
- Page 2 (see rear cover of this manual). The Manufacturer (Wavecom Instruments Pty. Ltd.) warrants its products against defects in materials and workmanship for a period of 12 months from the date of purchase. During the warranty period, the Manufacturer will repair (or at its option replace at no charge) the product that proves to be defective.
- Page 3 At Wavecom we take great pride in our customer service and support. We provide assistance, troubleshooting and support over the phone, via Skype or Facetime, via email or in person to help you get the most from your Wavecom Portable Appliance Tester. To be eligible for our support services you must register your product.
-
Page 4: Table Of Contents
Powering on the Tester Using the TnT Titan with WinPATS Setting up the Barcode Scanner LED Indicators TnT Titan Testing Menu – Main Menu A TnT Titan Testing Menu – Main Menu B Meter Mode ® [Not available in Battery Mode] Specifications... -
Page 5: Important Information
TnT Titan User Manual Wavecom Important Information Contents • • TnT Titan Portable Appliance Tester IEC Power Cable (10A units) • • WinPATS voucher (valued at $30+GST) for App Purchase IEC 20/10 Power Cable with Circuit Breaker (20A Units) •... -
Page 6: Tnt Titan Diagrams
Using the TnT Titan on Mains Power To use the TnT Titan on mains power, simply plug in the supplied power cable and connect it to a mains power outlet. Your TnT Titan will automatically connect to mains power and begin charging the battery. - Page 7 When sending the TnT Titan for calibration, please turn off the battery isolation switch which is located on the rear panel of the tester. If you have any questions about the battery of your TnT Titan please contact Wavecom for further advice.
-
Page 8: Using The Tablet
Using the Tablet The TnT Titan comes with an Android tablet to be used with the WinPATS App to control your tester, save your test results and generate reports. In the next section you will find a short introduction to using the TnT Titan with your tablet, and more detailed, step by step guides are available on our website - www.wavecom.com.au... -
Page 9: Operating The Tnt Titan
Tablet > USB-OTG > USB-A to Micro USB Cable > Micro USB port of your TnT Titan (located on the rear of your tester). See diagram on page 10. - Page 10 You may now be prompted to pair your two devices using a PIN code. If so, your TnT Titan will display a code on the screen. Enter this code into WinPATS and tap OK. You will be asked to confirm the connection - tap Confirm after checking the details are correct.
- Page 11 WinPATS will scan for any available TnT or TnP testers and display them in a list - select your tester from the list by tapping it. If you see multiple TnT or TnP products in the list, use the serial number of your TnT Titan to identify your tester.
- Page 12 TnT Titan User Manual Wavecom Connect your cables in the sequence shown below. Your TnT Titan USB-B port is located inside the storage compartment, and the Printer USB-B port is located at the rear of the printer. Micro USB to...
- Page 13 Select the best option for your situation. If you select Quick Test, select the test you wish to conduct from the list. Set up the item to be tested by plugging it into the TnT Titan (along with any accessories as required),...
- Page 14 Set up the item to be tested by plugging it into the TnT Titan (along with any accessories as required) then tap ‘Start Test’. Conduct the Visual Test, and if the item passes, the test will be conducted in stages automatically, and the results displayed on screen.
-
Page 15: Setting Up The Barcode Scanner
Your scanner should now be paired with your TnT Titan. To test your scanner, open the WinPATS App and return to the Home screen. Scan one of the barcodes on the outside of the scanner box, and you should see the barcode appear in the ‘Search Barcode’... -
Page 16: Led Indicators
User Manual Wavecom LED Indicators Battery LEDs The battery LED indicators display how much charge is remaining in your TnT Titan. Use the table below for reference. 100% - Battery is fully charged 20% (LED 2 will be flashing) 0% (LED 1 will be flashing) Indicator LEDs The indicator LEDs are used to display various statuses and results. -
Page 17: Tnt Titan Testing Menu - Main Menu A
You may also see more than one, or all of these turn red. For more information, see Mains Supply Test (Page 25) TnT Titan Testing Menu – Main Menu A If you are using your TnT Titan with the WinPATS App, you do not need to operate the TnT Titan manually - all functions can be controlled directly from the App. -
Page 18: Tnt Titan Testing Menu - Main Menu B
Class 2 appliance. Look for the double insulated symbol, seen here. 2. Plug the appliance into the appliance test socket of the TnT Titan 3. Navigate to Main Menu A, then Press the F2 key to begin the test 4. - Page 19 User Manual Wavecom TnT Titan Testing Menu – Main Menu B Use the Enter button to switch between Menu A and Menu B. All tests on Menu B require a Mains Power source. Power Test - Menu B – F1 The Power Test is for the purposes of monitoring and performance of equipment.
- Page 20 3. Plug the appliance into the Appliance Test Socket of the TnT Titan 4. If testing a Class 1 Appliance, plug the IEC Clamp Cable into the IEC socket of the TnT Titan, then clamp it onto earthed metal on the appliance 5.
- Page 21 Adjusting the current level: The TnT Titan displays and maintains the last set trip current value. If the user wishes to change the value of the trip current the following steps enable the changes. Press F2 from the options menu to display test current.
- Page 22 2. Navigate to Main Menu B, and press F3 to enter the RCD Menu, then press F1 to select Time Test 3. Press F3 to enter the Time Test options menu, to ensure your TnT Titan has the correct settings for the type of RCD 4.
-
Page 23: Meter Mode ® [Not Available In Battery Mode]
3. Press F2 to select your RCD Type, and turn Portable RCD testing on or off 4. Press F3 to begin the test - the TnT Titan will increase the current to the RCD until it trips, displaying the current on screen. - Page 24 TnT Titan User Manual Wavecom Watts A watt is the unit used to measure the amount of actual flowing electrical energy. Volt-Amps A volt-amp is the unit used to measure the apparent electrical power used by computing equipment. Mathematically, it is expressed as volts times amps (V*A). Because it represents the amount of energy computing systems may draw from a power grid, Volt-Amp measurements are used to determine the kind of wiring and circuit breakers required to support the computing equipment in question.
-
Page 25: Specifications
Current Ramp Trip Test: 0 to 500mA in 1mA increments. Power Measurement Leakage Current: 0 to 30.0mA at 200 to 265V Load Current: 0.0 to 10Amp (20Amp for TnT Titan 20A) Voltage: 200 to 265VAC Power Factor: 0.00 to 1.00... -
Page 26: Technical Information
Earth Terminal or Protective. To perform this test, a continuous earth loop must be made between the exposed conductive material (metal) and the TnT Titan appliance tester. This is done by means of connecting the earth lead with the crocodile... -
Page 27: Class 2 (Double Insulated) Construction
TnT Titan Range of appliance testers, these concerns are alleviated. The TnT Titan can safely test electronic equipment as the tests are carried from Active-Neutral (shorted by a relay inside the tester) to Earth. In this mode no dangerous voltages pass through to the internal components of the appliance, or Device Under Test (‘DUT’). -
Page 28: Leakage Test
NOTE: The maximum resistive load for the TnT Titan is 10 Amps, and the maximum load for the TnT Titan 20A is 20 Amps A Leakage Test applies power to the Device Under Test (DUT) and measures the imbalance of leakage current from the DUT between the active and neutral conductors. -
Page 29: Integrated Tests
This test function ensures that the appliance is plugged into the TnT Titan and that it is switched on. If the device is not plugged in and the TnT Titan detects that no device is present, and prompts the user to plug in an appliance to continue the test or press ‘QUIT’... -
Page 30: Wavecom Tags
All of the Wavecom tags are suitable for printing using every brand of thermal transfer printers available from around the world. The adhesive used on our tags is most aggressive and comes highly recommended for use in the electrical test and tag industry, there should be no butterflying once applied. - Page 31 At the time of developing this manual, all care and consideration for accuracy has been implemented. Wavecom accepts no responsibility for any errors or omissions in this document. This is partly based on the fact that Electronics & Electrical testing and specifications worldwide are constantly changing and that Local, State and National Regulatory Authorities may also have differing or additional requirements.
-
Page 32: Purchase Information
WinPATS Android App Discount Coupon (Valid for one use only) Purchase Information Date of Purchase Sold By The TnT Titan is proudly designed and manufactured in Australia by Wavecom. Wavecom SA Wavecom WA Wavecom VIC 257 Grange Road, Unit 2/17 Casino Street,...