Rear Panel Section; Block Diagram - Fostex VM88 Owner's Manual

Rear panel sectin
1. Digital in/out jacks
Digital signals (S/P DIF or ADAT) from external digital
equipment can be input to these DIGITAL IN jacks
and then assigned to the desired input channel. S/P
DIF or ADAT digital signals can be output from the
DIGITAL OUT connectors. For details, please refer to
"Connecting peripheral equipment" on page 9 and
"In/out of digital signals" explained in "Normal mix
mode" on page 18.
2. RESET switch
This switch resets the CPU inside VM88.
Refer to page 8 for details.
-48V
PHANTOM (SETUP)
INSERT
(-10dBV)
A/D
MIC
(-10dBu~-50dBu)
From DIGI IN
TRIM
LINE
(+10dBu~-30dBu)
CH 1
CH 2
CH 3
CH 4
A/D
CH5 INPUT
A/D
(+4dBu~-40dBu)
TRIM DIGI IN
(SETUP)
CH6 INPUT
(+4dBu~-40dBu)
From DIGI IN
TRIM
CH5/6
CH7/8
DIGI IN
To CH1
To CH2
S/P DIF
To CH3
or
To CH4
ADAT
To CH5
DECODE
To CH6
DIGI IN
(SETUP)
To CH7
To CH8

Block Diagram

To DIGI OUT
To METER
100Hz 1kHz 10kHz
CH ON
GAIN
LO MID HI
To DIGI OUT
To METER
100Hz 1kHz 10kHz
CH ON
MONO/STEREO
GAIN
(SETUP)
LO MID HI
EFF 1-2
ASP
DIGITAL EFFECT
EFF 1
MASTER
Model VM88 Owner's Manual
3. POWER switch
The On/Off power switch.
4. AC IN connector [AC IN]
Plug-in the power cable included with the VM88 here.
< NOTE >
If the VM88 is not to be used for long periods (more
than one month) be sure to remove the power cable
plug from the wall outlet.
ST EFF AUX
L R 1 2 1 2
ST MASTER
PAN
EFF 1
EFF 2
AUX 1 AUX MASTER
AUX 2
PRE/POST
MON
PAN
EFF 1
EFF 2
AUX 1
AUX 2
PRE/POST
From CH1-A/D
From CH2-A/D
From CH3-A/D
From CH4-A/D
From CH5-A/D
EFF MUTE
From CH6-A/D
From CH7-A/D
From CH8-A/D
7
To DIGI OUT
D/A
100Hz 1kHz 10kHz
D/A
CH ON
ST MASTER
To METER
LO MID HI
D/A
AUX 1
MASTER
D/A
AUX 2
MASTER
From AUX 1
AUX 1
From AUX 2
AUX 2
From ST
ST
MON SEL
DIGI OUT
S/P DIF
From ST
ENCODE
ADAT
ENCODE
DIGI OUT
S/P DIF
ADAT
(SETUP)
L
R
ST OUT
ST OUT (+4dBu)
L
R
To MON
ST OUT
(-10dBV)
To MON
AUX 1 OUT
(-10dBV)
To MON
AUX 2 OUT
(-10dBV)
L (M)
R
SUB IN
(-10dBV)
L (M)
R
MON OUT
(-10dBV)
PHONES
(100mW)