c) Prevent unintentional starting. Ensure the GENERAL POWER TOOL SAFETY switch is in the off -position before connecting WARNINGS to power source and/or battery pack, picking up or carrying the tool. WARNING Carrying power tools with your fi nger on the switch Read all safety warnings, instructions, illustrations and or energising power tools that have the switch on specifi...
Slippery handles and grasping surfaces do not ADDITIONAL SAFETY WARNINGS allow for safe handling and control of the tool in unexpected situations. 1. Always charge the battery at a temperature of 0 oC – 40 oC. A temperature of less than 0 oC will result in over 5) Battery tool use and care charging which is dangerous.
18. Chip cover 37. Keep the tool’s terminals (battery mount) free of swarf ○ Chip cover prevents chips from fl ying off and improves and dust. the effi ciency of dust collector. ○ Prior to use, make sure that swarf and dust have not ○...
12. Do not immerse the battery or allow any fl uids to fl ow USB DEVICE CONNECTION inside. Conductive liquid ingress, such as water, can PRECAUTIONS (UC18YSL3) cause damage resulting in fi re or explosion. Store your battery in a cool, dry place, away from combustible and When an unexpected problem occurs, the data in a USB fl...
Weight 3.0 kg 2.9 kg (BSL36B18) (BSL36B18) Existing batteries (BSL3660/3620/3626, BSL18xx series, etc.) cannot be used with this tool. NOTE Due to HiKOKI’s continuing program of research and development, the specifi cations herein are subject to change without prior notice.
Page 15
2. Battery CHARGING Model BSL36A18 BSL36B18 Before using the power tool, charge the battery as follows. Voltage 36 V / 18 V (Automatic Switching*) 1. Connect the charger’s power cord to the receptacle. 2.5 Ah / 5.0 Ah 4.0 Ah / 8.0 Ah When connecting the plug of the charger to a receptacle, Battery capacity the charge indicator lamp will blink in red (At 1- second...
(2) Regarding the temperatures and charging time of the rechargeable battery The temperatures and charging time will become as shown in Table 2. Table 2 Charger UC18YSL3 Type of battery Li-ion Temperatures at which the 0°C – 50°C battery can be recharged Charging voltage 14.4 Multi volt...
Page 17
*4 How to use the LED light Pocket cutting <CJ36DA> Angular cutting NOTE To prevent the battery power consumption, turn off the Concerning cutting of stainless steel LED light frequently. The light goes out automatically plates 10 seconds after the switch is released. Connecting with cleaner (sold separately) <CJ36DB>...
SELECTION OF BLADES Important notice on the batteries for the HiKOKI cordless power tools Accessory blades Please always use one of our designated genuine To ensure maximum operating effi ciency and results, it is batteries. We cannot guarantee the safety and...
Page 19
Table 5 List of appropriate blades Blade No. 1 (Super No. 11 No. 12 No. 15 No. 16 No. 21 No. 22 No. 41 No. 97 long) Material to be cut Thickness of material (mm) Material quality General lumber Below 135 10 - 55 Below 20 10 - 55 5 - 40 10 - 65...
TROUBLESHOOTING Use the inspections in the table below if the tool does not operate normally. If this does not remedy the problem, consult your dealer or the HiKOKI Authorized Service Center. 1. Power tool Symptom Possible cause Remedy Tool doesn’t run No remaining battery power Charge the battery.
Page 21
The charger’s vents are blocked, causing its Avoid blocking the vents. internal components to overheat. The cooling fan is not running. Contact a HiKOKI Authorized Service Center for repairs. The USB power lamp The battery’s capacity has become low. Replace the battery with one that has has switched off...
Need help?
Do you have a question about the CJ 36DA and is the answer not in the manual?
Questions and answers