ATTENTION: This device is only suitable for professional use! Protection class IP 20 - only for use in dry environments (indoors)! ATTENTION: JB-Lighting Lichtanlagentechnik GmbH does not authorise the use of its devices in life support systems. Life-supporting systems are systems whose purpose is to maintain or stabilise life and whose defect or malfunction may result in death or injury to persons.
Page 7
P1 8 MK2 WasH ATTENTION: This fixture corresponds to protection class I. For this reason, this spotlight must be connected to a mains socket with earthing contact. Never connect this device to a dimmer pack. During first use, some smoke and odour may occur. This is normal and does not necessarily mean that the device is defective.
P1 8 MK2 Wash ATTENTION: The distance between the light emission and the surface to be illuminated must be at least 2.0 metres. The maximum ambient temperature of 45°C must not be exceeded. ATTENTION: The front lens must be replaced if it is visibly damaged to the extent that its function is impaired, e.g.
P1 8 MK2 WasH Connection outside Europe: The P18 MK2 Wash may only be operated on the following power supply systems: ATTENTION: Mains In Canada, the P18 MK2 Wash may Wash only be operated in a 2-wire, 1 phase network with a maximum voltage of 2 wires, 1 phase 120V! 3 wires, 1 phase...
P1 8 MK2 Wash 4.4 Signal connections 4.4.1 DMX cabling The DMX cabling (signal lines) should be done with a 4-pin cable with shielding. We recommend a DMX cable (110 Ohm, 4x0.22mm ), alternatively a 2-pole micro cable can be used. The plugs and sockets are 5-pin XLR connectors, which can be purchased in specialist shops.
✔ ✔ To mount the unit on a trussing system use two of the original JB-Lighting omega brackets with original Camloc-connectors. You have following four possibilities to mount the omega brackets. 258,4 The Camlocs must snap in to be locked properly. Ensure that the structure (truss) to which you are attaching the fixture is secure.
P1 8 MK2 Wash 5. Control panel The P18 MK2 Wash has a graphic colour touch display that can be rotated 180° when installed in a suspended position. The display can be rotated in the PERSONALITY MENU or via short cut ENTER + UP in the main screen.
Page 13
"JB-Lighting" is displayed means no DMX signal is present. A very rapidly flashing display illumination when "JB-Lighting" is displayed means that a new error has been stored in the "ERROR LIST", also an error message in the display (e.g. *PAN TIMEOUT) indicates this current error.
P1 8 MK2 Wash 5.1 Menu overview ENTER ENTER ENTER FACTORY DEF. LOAD DEFAULTS SURE? USER DEFAULTS LOAD DEFAULTS SURE? SAVE DEFAULTS SURE? PASSWORD DMX / NET ADDR DMX ADDRESS ADDRESS +/- ARTNET ADDRESS ADDRESS +/- SACN ADDRESS ADDRESS +/- DMX INPUT CONFIG WIRELESS ON/OFF...
Page 15
P1 8 MK2 WasH RESET FIXTURE SURE? SERVICE ERROR LIST LIST PAN TIMEOUT COUNT: 1 CLEAR? CLEAR SURE? FUNCTION TEST START TEST TEST RUNNING DMX TEST DMX CHANNEL CH 001: --- INIT PAN/TILT SURE? DISPLAY CONTR. D. CONTR: +000 +/- FINE ADJUST OFS PAN OFS PAN +/-...
P1 8 MK2 Wash SOFTWARE VER. INFO FIXTURE ID TOT OP. TIME TOT LAMP TIME TOT BAT CHARGE T. TEMP BASE LCD ACTUAL RESET? TEMP BASE PS ACTUAL RESET? TEMP HEAD MAIN ACTUAL RESET? TEMP HEAD DRV ACTUAL RESET? TEMP HEAD LED ACTUAL RESET? TEMP HEAD AMB.
Page 17
P1 8 MK2 WasH Under IP ADDRESS -> DEFAULT IP this can be changed from the network 10.xxx.xxx.xxx to a network 2.xxx.xxx.xxx. For your own self-definable IP address, you can set your own desired IP address under IP ADDRESS -> USER-IP. This address is divided into BYTE1 to BYTE 4 and can be set one after the other.
Page 18
P1 8 MK2 Wash There is no danger to the life of the device in any mode, as the P18 MK2 Wash has a temperature safety shutdown. In addition, the LED module is switched off from an ambient temperature of 60°C! PAN TILT SPEED - setting pan/tilt speed In the PAN TILT SPEED menu you can set the maximum speed, the acceleration and thus also...
P1 8 MK2 WasH LED FADE OUT - type of dimming Used to set how to dim the lower range from 0-5%. STANDARD: When dimming the headlamp, all LED's dim out at the same time. SOFT: When the headlamp is dimmed, the LED's are dimmed out in groups (in a row) one row after the other.
P1 8 MK2 Wash Operation via master-slave function: Connect the P18 MK2 Wash via DMX lines and activate the REMOTE menu item for all slave devices. To do this, navigate in the STANDALONE menu to the REMOTE sub-menu. Activate the REMOTE function by pressing and holding “ENTER”, and also pressing “ESC”. The spotlight is in slave mode when the display shows the status REMOTE INACTIVE or REMOTE ACTIVE.
P1 8 MK2 WasH 6. Control options 6.1 DMX 6.1.1 Operating modes The P18 MK2 Wash has 2 different DMX modes. The respective mode can be set in the PERSONALITY- DMX MODE menu item. The set mode is displayed in the main menu. Mode 1(M1) Mode 2 (M2) Channel 1...
Page 22
P1 8 MK2 Wash Channel 42 Magenta Channel 43 Fine magenta Channel 44 Yellow Channel 45 Fine yellow Channel 46 CTO (CTB model WW) Channel 47 CTO fine (CTB fine model WW) Channel 48 Sparkle Channel 49 Sparkle speed Channel 50 Frost 1 Channel 51 Frost 2...
P1 8 MK2 WasH 6.1.2 DMX channel assignment Mode 1 and Mode 2 Function Pan (X) movement 546.74° 000-255 Pan (X) fine (16 Bit) 000-255 Tilt (Y) movement 281.16° 000-255 Tilt (Y) fine (16 Bit) 000-255 Control channel To enable uniform dimming manually via faders for all light mixing consoles, 5 diffe- rent settings for the DMX smoothing are available.
Page 24
P1 8 MK2 Wash Setting for maximum DMX smoothing Dimmer fade out via fader (fast - slow) 128-135 DIMMER CURVE - selection of dimmer curve LINEAR - linear dimmer curve 136-136 SQUARE - exponential dimmer curve 137-137 SQUARE INVERSE - exponential inverse dimmer curve 138-138 not used 139-139...
Page 25
P1 8 MK2 WasH Shutter Shutter closed 000-015 Shutter open 016-095 Open pulsing shutter >20Hz (rapid - slow) 096-110 Shutter open 111-111 Fade effect with dimmer (slow - rapid) 112-125 Shutter open 126-126 Shutter closed 127-126 Open pulsing shutter <20Hz (rapid - slow) 128-142 Shutter open 143-143...
P1 8 MK2 WasH 6.1.3 Control channel Via the control channel different functions of the fixture can be permanently switched. The follo- wing functions can be switched via the control channel. Response of the headlamp when dimming via faders BACKLIGHT MODE - display backlight DISPLAY ORIENTATION - display orientation MAIN SCREEN MODE - main screen view USER FIXTURE ID SET - set headlight number...
P1 8 MK2 Wash 6.5 RDM The P18 MK2 Wash can communicate via RDM (Remote Device Management) in accordance with ESTA American National Standard E1.20-2006. RDM is a bidirectional communication protocol for use in DMX512 control systems. It is the open standard for the configuration and status monitoring of DMX-512 devices.
The P18 MK2 Wash stores all occurring errors internally. An error message can have a harmless cause. If you experience frequent error messages, please contact your dealer or the JB-Lighting service department. All error messages are displayed with the respective frequency and can be deleted.
P1 8 MK2 WasH 7.2 Changing gobos To open the device (from the right side) place the spotlight on a firm base as shown in the picture, the display (1) facing you, the tilt lock (2) is on the right side and the spotlight head facing away from you (3) (Or look through the grille into the spotlight from behind and look at the arrow showing...
P1 8 MK2 Wash 7.4 Cleaning the device You should check the function of the fans in the head and foot at regular intervals. Above all, make sure that the air intakes and the interior of the P18 MK2 Wash are free of fluff and dust. To do this, open the head cover (4x camlocks (4) with half a turn) and the base plate on the foot.
P1 8 MK2 WasH 7.5 Service and maintenance On the P18 MK2 Wash, the zoom / focus guide rails and the rotating gobos should be checked for sufficient lubrication at regular intervals - once a year. To do this, open the head cover (4x camlocks with half a turn), the zoom cover (3 Phillips screws) see picture (4) and picture (5) and remove the gobo insert (2 knurled screws).
Directive: 2014/30/EU Electromagnetic compatibility (Directive 2014/30/EU of the European Parliament and of the Council of 26/02/2014 to approximate the laws of the Member States relating to electromagnetic compatibility) The manufacturer, JB-Lighting Lichtanlagentechnik GmbH Sallersteigweg 15 89134 Blaustein-Wippingen P18 MK2 Wash declares that the product: complies with the essential protection requirements of the directives.