Advertisement
Quick Links
The Lear Universal Garage Door Opener (LEAR Car2U ™) is a universal transmitter and can
replace up to three different remote control transmitter units used to operate the following types
of devices:
Garage Door Opener
Security Devices
Home Lighting Systems
Additional Lear Car2U ™ information can be found on the internet at
calling 1-866-57Car2U.
Types of Garage Door Openers (Fixed Code and Rolling Code)
Lear UGDO™ has the capability of programming rolling code and fixed code garage door
openers:
Rolling code garage door openers are used for garage doors produced after 1996 and are
code protected. Rolling code means the coded signal is changed every time your remote
control garage door opener is used.
Fixed code garage door openers are used for garage doors produced prior to 1996. Fixed
code uses the same coded signal every time, which is manually programmed by setting
DIP switches for a unique personal code.
If you do not know if your garage door opener is a rolling code or fixed code device, open your
garage door opener's remote control battery cover. If a panel of DIP switches is present as
shown in the typical remote device shown below, your garage door opener is a fixed code device.
If not, your garage door opener is a rolling code device.
Lear UGDO Owner's Guide Version 3.2 Page 1
Lear UGDO
Lear Car2U Transmitter
Short Term Confidentiality Requested
www.learcar2U.com
or by
3/27/2006
Advertisement
Related Manuals for Lear UGDO
Summary of Contents for Lear UGDO
- Page 1 Short Term Confidentiality Requested Lear UGDO Lear Car2U Transmitter The Lear Universal Garage Door Opener (LEAR Car2U ™) is a universal transmitter and can replace up to three different remote control transmitter units used to operate the following types of devices:...
- Page 2 Lear UGDO Programming the Lear UGDO™ Transmitter Depending on your garage door opener manufacturer, Lear UGDO™ provides two easy ways to program your garage door opener. 1. Rolling Code Garage Door Openers: If your garage door opener is a rolling code device and do not have a row of dip switches use the “Programming Rolling Code Garage Door...
- Page 3 Make sure that your key is ON and engine OFF while programming the transmitter. Use the following steps to program up to three different devices. Lear UGDO Owner’s Guide Version 3.2 Page 3 3/27/2006...
- Page 4 Lear UGDO Programming Rolling Code Garage Door Opener or Device 1. Firmly PRESS the outer two Lear UGDO™ buttons for one — two seconds and immediately release them. 2. Go to the garage. Locate the garage door motor head and Press and Release its “learn”...
- Page 5 To program another button with a fixed code, perform steps 1 – 5 of “Programming Fixed Code Garage Door Opener or Device” on page 6 substituting a different function button in Step 5 than what you used for the garage door opener. Lear UGDO Owner’s Guide Version 3.2 Page 5 3/27/2006...
- Page 6 Car2U. Push one Button for each switch as follows: Left Button = “On” switch position Right Button = “Off” switch position Middle Button = “Middle” switch position Lear UGDO Owner’s Guide Version 3.2 Page 6 3/27/2006...
- Page 7 Do not release the button until you see the garage door move. Most garage doors open quickly. However, some garage doors may take from one to two and a half minutes to open for the initial garage door opener programming. Lear UGDO Owner’s Guide Version 3.2 Page 7 3/27/2006...
- Page 8 (fixed and rolling code) are erased. FCC and RSS-210 Industry Canada Compliance If your vehicle is equipped with a Lear Car2U ™ transmitter, it complies with Part 15 of the FCC Rules. Operation is subject to two following conditions: 1.