Page 1
DIAMOND CORE DRILL SPJ-122He-U INSTRUCTION MANUAL ◎ Thank you for purchasing our products. ◎ Before using, please read Instruction manual carefully, and use the machine safety by following the instructions. ◎ After reading, please keep it where anyone can utilize.
Page 2
Read the operating instructions before use. Only for EU countries Disposal of electric tools together with household waste is not permissible! In observance of European Directive on waste electrical and electronic equipment and its implementation in accordance with national law, electric tools that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility.
1. WARNING AND CAUTION ◎ To avoid the risk of fire, electric shock and personally injury, follow all the instruction mentioned in "Safety Notice for Electric Tools" and "Notes for Usage of Core Drill". ◎ Before using, please read "WARNING & CAUTION", and follow the instructions for your safety. ◎...
Page 5
WARNING 11. Use CONSEC recommended accessories and options. ◎ In case that you use the accessories and the options which are not listed in the manual or CONSEC's catalogue, it might cause the accidents or personal injury. Please do not use the accessories and the options which CONSEC does not recommend.
【2】Notes for Usage of Core Drill (In case of combination with CONSEC's original Pole Base.) WARNING 1. Check for the embedded conduit etc. ◎ In case that you contact to the electric wire or conduit in that there are electric current, you may receive the electric shocks.
Page 7
WARNING 16. In case that Pole Base is fixed, ensure to fix it at stable place. 17. If accessories are broken, don’t use it. Repair or replace. 18. Check the Core Bit, tube and coupling with no crack, tipping or deformation by visual confirmation.
3. SPECIFICATIONS Model SPJ-122He-U Motor Single phase series commutator motor Power supply Single-phase A.C. 110V 50Hz Rated current Max. output 1500W No load speed 900min Standard Bit diameter 14.5~120mm Max. Bit diameter 160mm outside Unified screw(1-1/4”-7 UNC) Core Bit installing screw...
6. GENERAL DRAWING AND SPECIFICATIONS IN OPERATION ◎ Drill Head installed on to □40 Pole Base. Feeding handle □40 Pole Base Drill Head Bolt square washer Hex. nut Core Bit Leveling Bolt Water Collector Water collector fitting - -...
7. OPERATIONAL INSTRUCTIONS (Explanation referring to general drawing during operation.) 【1】 Anchoring Core Drill ◎ Core Drill can be anchored by means of anchor bolt, Vacuum Pad or Support jack. Follow the below procedures for bolt anchor method. 【2】 Anchoring Core Drill by Anchor Bolt 1.Installation of anchor bolt 1) Drill anchor bolt hole, using a hammer drill.
Page 12
.Core drilling WARNING When drilling a through-hole, take proper measures to provide for protection on the other side where Core Bit penetrates. 1) Turn switch off and plug in. WARNING To prevent accidental starting, make certain that motor switch is in OFF position before plugging your machine.
8. MAINTENANCE AND INSPECTION 【1】 Maintenance 1) Clean the surface of the machine after using. Regarding the outer frame of the Drill Head, the part of the Gear case is made of aluminum, and the part of the motor is made of the sturdy synthetic resin. If gasoline, thinner, petroleum or kerosene are adhered to the outer frame of the Drill Head, the surface of the Drill Head will be damaged.
Page 14
2.Inspection ・Adjustment for drill carriage adjustment part. ◎ Adjust the clearance between the Pole and Drill Carriage ASSY. by moving the Feeding handle, and screw 6 places of Drill carriage adjustment screw on the part of Drill Carriage ASSY. by screwdriver in a balanced.
11. WARRANTY We will guarantee the HAKKEN Core Drill SPJ-122He-U for 6 months from the date of delivery. During this period we will rectify material and production defects free of charge. We are not responsible for any other damage direct nor indirect other than this. This warranty...
Page 20
Main office : 4-6-8 Shoko Center Nishi-ku Hiroshima 733-0833 Japan International Department : 1-7-5-1, Sakaimachi, Naka-ku, Hiroshima, 730-0853 Japan Phone : 81-82-297-3231 Fax : 81-82-297-3230 E1791-1 - -...