Save the carton and all packing materials. In the event that a fixture must be returned to the factory, it is important that the fixture be returned in the original factory box and packing. Your shipment includes: Showtec Helios 150 COB, 5600K Pro power cable (1,5 m) ...
Page 4
• If your Showtec device fails to work properly, discontinue the use immediately. Pack the unit securely (preferably in the original packing material), and return it to your Showtec dealer for service.
Helios 150 COB, 5600K Operating Determinations • This device is not designed for permanent operation. Consistent operation breaks will ensure that the device will serve you for a long time without defects. • The minimum distance between light output and the illuminated surface must be bigger than 1 meter.
Helios 150 COB, 5600K The Helios can be placed on a flat stage floor or mounted to any kind of truss with a clamp. Improper installation can cause serious injuries and/or damage of property! Connection with the mains Connect the device to the mains with the power-plug.
Helios 150 COB, 5600K Return Procedure Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued. Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility.
Helios 150 COB, 5600K Description of the device Features The Showtec Helios 150 COB 5600K is a light fixture with high output and great effects. Input voltage: 100-240V AC, 50/60Hz Power consumption: 210W Light source: 1 x 150W COB 5600K ...
10) 5-pin DMX signal connector OUT Installation Remove all packing materials from the Helios 150 COB 5600K. Check if all foam and plastic padding is removed. Connect all cables. Do not supply power before the whole system is set up and connected properly.
Helios 150 COB, 5600K Set Up and Operation Follow the directions below, as they pertain to your preferred operation mode. Before plugging the unit in, always make sure that the power supply matches the product specification voltage. Do not attempt to operate a 120V specification product on 230V power, or vice versa.
Helios 150 COB, 5600K Multiple Helioses (DMX Control) 01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation. 02) Always use a safety cable (ordercode 70140 / 70141). 03) Use a 3-pin/5-pin XLR cable to connect the Helioses and other devices.
Helios 150 COB, 5600K Fixture Linking You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to run synchronized shows of two or more fixtures set to a master/slave operating mode. The combined number of channels required by all the fixtures on a serial data link determines the number of fixtures the data link can support.
Helios 150 COB, 5600K The Helios 150 COB 5600K can be operated with a DMX controller in control mode or without a DMX controller in stand-alone mode. Control Panel A) LCD display MODE button C) SETUP button D) UP button DOWN button Fig.
4. Sound-controlled mode 5. Dimmer mode 6. Settings 7. Information The Helios 150 COB 5600K will show its version number at start-up! 1. Auto With this menu you can activate Auto mode. 01) Press the MODE button until the display shows 02) Press the SETUP button to open the menu.
Helios 150 COB, 5600K 4. Sound-controlled mode With this menu you can set the sound sensitivity. 01) Press the MODE button until the display shows 02) Press the SETUP button to open the menu. 03) Press the UP/DOWN buttons to select the required sensitivity from , from OFF to high sound sensitivity.
Helios 150 COB, 5600K 6.4. Factory Reset 01) Press the UP/DOWN buttons until the display shows 02) Press the SETUP button to open the menu. 03) Press the UP/DOWN buttons to choose between Yes and No. 04) Press the SETUP button to confirm your choice.
04) The electric power supply cables must not show any damages or material fatigue. The Helios 150 COB 5600K requires almost no maintenance. However, you should keep the unit clean. Otherwise, the fixture’s light output will be significantly reduced. Disconnect the mains power supply, and then wipe the cover with a damp cloth.
Page 19
Check if power is switched on and No power to the fixture One or more cables are plugged in fixtures do not function at all • Return the Helios to your Showtec Internal fuse blown dealer. Fixtures reset The controller is not connected. • Connect controller.