Table of Contents
Advertisement
Power Indicator
Mode
Power ON
Power OFF and Power Save "AUTO
STANDBY"
Power consumption under 0.5 W*
2
Power Save "AUTO POWER SAVE"
Power consumption under 6.0 W
Power Standby when "SCHEDULE
SETTINGS" enabled
Diagnosis (Detecting failure)
*1 If "OFF" is selected in POWER INDICATOR (page 27), the LED will not light when the
LCD monitor is in active mode.
*2 Without any option, with factory settings.
Initial settings
Setting LAN POWER (see page 28) and POWER SAVE (see
page 27) windows appear the fi rst time the power is on.
These settings are only necessary upon initial setup.
However, this message window appears when the power is
on after FACTORY RESET is done.
When LAN POWER is set to ON and POWER SAVE is set to
"DISABLE" after FACTORY RESET, then the monitor power
is off and on again, the message window will not appear.
Using Power Management
The LCD monitor follows the VESA approved DPM Display
Power Management function.
The power management function is an energy saving
function that automatically reduces the power consumption
of the display when the keyboard or the mouse has not been
used for a fi xed period.
The power management feature on your new display has
been set to the "AUTO STANDBY" mode. This allows your
display to enter a Power Saving Mode when no signal is
applied. This could potentially increase the life and decrease
the power consumption of the display.
NOTE:
Depending on the computer and video card used,
this function may not operate.
NOTE:
The monitor automatically goes into OFF at the
preset time period after signal is lost.
MULTI PICTURE MODE
Selects MULTI PICTURE MODE. You can select up to
4 pictures. When MULTI PICTURE is "ON" and PICTURE
NUMBER is 2 PICTURES, the display images are like below.
PIP
2
A
PICTURES
A
B
When MULTI PICTURE is "ON" and PICTURE NUMBER is
3 PICTURES, the display images are like below.
PIP
3
A
PICTURES
A
B
C
When MULTI PICTURE is "ON" and PICTURE NUMBER is
4 PICTURES, the display image is set to like below.
A
B
4
PICTURES
C
D
MULTI PICTURE MODE (See page 25).
Status Indicator Light
1
Green*
Red
Amber
Green and Amber blink alternately
Red Blinking
(See Troubleshooting page 49)
PBP1
B
PBP1
PBP2
PBP3
A
B
B
C
A
C
C
A: PICTURE 1
B: PICTURE 2
C: PICTURE 3
D: PICTURE 4
Aspect
DVI1, DVI2, DPORT, OPTION*
FULL
1:1
ZOOM
HDMI1, HDMI2, HDMI3, HDMI4, PRESET1*
FULL
WIDE
DYNAMIC
*4: This function depends on which option board you use.
*5: This function depends on INPUT CONFIGURATION setting.
Aspect ratio
Unchanged view*
of image
4:3
Squeeze
Letterbox
NORMAL: Displays the aspect ratio the same as it is sent
from the source.
FULL: Fills entire screen.
WIDE: Expands a 16:9 letter box signal to fi ll entire screen.
DYNAMIC: Expands a 4:3 pictures to fi ll the entire screen
with non-linearity. Some of the outside image area will be cut
off due to expansion.
1:1: Displays the image in a 1 by 1 pixel format.
ZOOM
The image can be expanded beyond the active display area.
The image which is outside of active display area is not
shown.
ZOOM
B
English-17
4
, PRESET1*
5
, PRESET2*
NORMAL
5
, PRESET2*
1:1
ZOOM
NORMAL
Recommended selection
3
for picture aspect*
NORMAL
DYNAMIC
FULL
WIDE
*
3
Grey areas indicate unused portions of the screen.
ZOOM
5
5
3
Advertisement
Table of Contents
