Initial Setup - Magnavox 55MV314X Owner's Manual

These Operations are accessible by Remote Control.
Some may also be accessible by the Main Unit's Control Panel.

Initial Setup

This section will guide you through the Unit's Initial setting which includes
selecting a Language for your On-screen Menu, country, location and
Autoprogram, which Automatically scans and memorizes viewable
channels. You can also set the network connection in this setting.
Before you begin:
Make sure the Unit is connected to an Antenna or Cable.
1
After making All the Necessary Connections, press B to Turn On
the Unit.
It may take a few moments to Turn On the Unit for the first time.
●
Initial setup menu appears Automatically after the Unit is Turned
●
On.
2
Use H I to select the on-screen language, country, location on the
right side of the TV screen, then press OK.
You must set Home in location setting. Otherwise, Picture and
●
Sound settings you adjusted will not be memorized after the Unit
goes into Standby mode.
3
Use H I to select the signal type.
If the TV is connected to a Cable or Satellite Set-top box, select
●
the 2nd one and skip to step 5.
To set up a TV signal from a cable TV
wall jack or a standard TV antenna.
To set up a TV signal from a cable TV
box or satellite TV receiver.
4
Use H I to select Antenna for TV channels or Cable for CATV
channels, then press OK.
Make sure that you have
attached your antenna or cable
signal into the jack on the rear side
of your TV labeled "ANTENNA
IN".
Now select either Antenna or
Cable, using up/down key on the
remote control. Once you have
made your selection, press the
OK button to proceed.
When Antenna is selected, the TV detects Antenna signals. It
–
searches for DTV and Analog TV channels available in your area.
When Cable is selected, the TV detects signals supplied by
–
cable. It searches for DTV, Analog TV and Cable channels
available in your area.
Autoprogram will begin.
●
5
Select
Select
6
Antenna
Cable
Skip
After an Initial Setup is completed...
●
●
●
●
●
●
System searching. Please wait...
Digital channels found:
Analog channels found:
Auto programming may take more than 20 minutes to
complete. Digital channels will take longer than
Analog to find and program. Please wait until you see
the Auto Programming complete message.
Stop
After the channel installation is completed, Network setup screen
will appear. Use H I to select Wireless or Wired, then press OK.
This TV can be connected to
your Internet home network.
Select your connection type.
Skip
If you have a Wireless router, select Wireless to
Wireless
connect to the Internet.
If you connect with an Ethernet cable, select Wired
Wired
to connect to the Internet.
If you have a router with WPS function, select Wireless and use
●
H I to select Simple Connect, then press OK.
Follow the on-screen instructions to complete the installation.
When you select On in the selection screen for Auto software
●
update. A message will appear if there is the latest software on the
network server.
Network updates will appear after Connection test succeeds.
●
Use J K to select Yes, then press OK.
When the initial setup is completed, the lowest memorized
●
channel with the confirmation message will be displayed on the TV
screen.
Note(s)
If you are not receiving a signal from your Cable service, contact the Cable provider.
●
If you press B during autoprogram, this setup of TV channels will be cancelled.
●
The Initial Autoprogram function can be executed for either Antenna or Cable only once.
●
When you change the connection (Antenna / Cable), select Autoprogram again. L
p. 31
If you want to scan the channels Automatically again.
Autoprogram L p. 31
You can add the desired channels not memorized by Autoprogram
through antenna connection.
Weak channel installation L p. 32
If you want to change to another Language. Language L p. 31
If you want to change the Country setting. Country L p. 20
If you want to change the Location setting. Location L p. 32
If you want to change the Network setting. Network L p. 34
18
0
0
Wireless
Wired
.
English