Clarke 07127A Operator's Manual
American b-2+ dc 7" edger
Hide thumbs
Also See for 07127A:
- Operator's manual (45 pages) ,
- User manual (8 pages) ,
- Operator's manual (44 pages)
Table of Contents
Advertisement
Quick Links
American
Operator's
B-2+ DC
Manual
7" Edger
READ THIS BOOK
This book has important information for the use and safe operation of this machine. Failure to read
this book prior to operating or attempting any service or maintenance procedure to your Clarke
American Sanders machine could result in injury to you or to other personnel; damage to the machine
or to other property could occur as well. You must have training in the operation of this machine
before using it. If cannot read English, have this manual explained fully before attempting to operate
this machine.
Si Ud. no pueden leer el Inglés, se hagan explicar este manual completamente antes de tratar el
manejo o servicio de esta máquina.
All directions given in this book are as seen from the operator's position at the rear of the machine.
For new books write to: Clarke, 2100 Highway 265, Springdale, Arkansas 72764
Form No. 70896A
11/04
Printed in the U.S.A.
Advertisement
Table of Contents
Related Manuals for Clarke 07127A
Summary of Contents for Clarke 07127A
- Page 1 This book has important information for the use and safe operation of this machine. Failure to read this book prior to operating or attempting any service or maintenance procedure to your Clarke American Sanders machine could result in injury to you or to other personnel; damage to the machine or to other property could occur as well.
-
Page 2: Table Of Contents
How to Check the Carbon Brushes ........12 Assembly Drawing #1 ..............14 Assembly Parts List #1 .............. 15 Assembly Drawing #2 ..............16 Assembly Parts List #2 .............. 17 Wiring Diagram ................18 Page 2 Clarke American Sanders American B-2 Operator's Manual... -
Page 3: Operator Safety Instructions
• Do not empty the contents of the dust bag into a fire. • Hitting a nail while sanding can cause sparks and create an explosion or fire. Always use a hammer and punch to countersink all nails before sanding floors. Clarke American Sanders American B-2 Operator's Manual Page 3... - Page 4 Maintenance and repairs performed by unauthorized personnel could result in damage or injury. Maintenance and repairs performed by unauthorized personnel will void your warranty. Servicing of this unit must always be referred to an authorized Clarke American Sanders distributor. CAUTION: Use of this equipment to move other objects or to climb on could result in injury or damage.
-
Page 5: Introduction And Machine Specifications
Cord Height (overall) 13½" 13½" Diameter " " Disc Diameter 7" 7" Weight 32 lbs. 32 lbs. Shipping Weight 46 lbs. 46 lbs Warranty 1 year limited 1 year limited Clarke American Sanders American B-2 Operator's Manual Page 5... -
Page 6: Machine Set-Up
4. To empty the dust bag, unzip the disposal flap and force contents out by inverting the bag. NOTE: For best results, empty frequently. Follow all warnings posted in this manual and on the dust bag. Page 6 Clarke American Sanders American B-2 Operator's Manual... -
Page 7: How To Prepare The Machine For Operation
5. Put one hand on the sandpaper. Using the special wrench, turn the screw clockwise with the other hand. Make sure the screw is tight. See Figure 2. Figure 2 Clarke American Sanders American B-2 Operator's Manual Page 7... -
Page 8: Sanding Cuts And Sandpaper
For final sanding of certain hardwoods and conifers where a smooth surface is desired. 120 grit For finishing cut on certain conifers. 150 grit For finishing cut on certain conifers where a smooth surface is desired. Page 8 Clarke American Sanders American B-2 Operator's Manual... -
Page 9: How To Operate The Machine
Mainte- nance and repairs performed by unauthorized personnel will void your warranty. Servicing of these units must always be referred to an autho- rized Clarke American Sanders distributor. Clarke American Sanders American B-2 Operator's Manual Page 9... -
Page 10: The Dust Control System
1. To clean the ventilation opening in the center of the plug, remove the plug from the machine. With the plug removed, also inspect the grease in the gearbox. See figure 9. Figure 9 Page 10 Clarke American Sanders American B-2 Operator's Manual... -
Page 11: Lubrication
Damage could occur to the gear box. 5. Remove the cover from the gear housing. 6. Remove the old lubricant from the gearbox. 7. Add ten ounces of Clarke American Sanders lubricant to the gearbox. Figure 11 CAUTION: To prevent damage to the motor, do not add more than ten ounces of lubricant to the gearbox. -
Page 12: How To Check The Carbon Brushes
14. Start up the machine, if sparking between either brush and the commutator occurs, use a brush seating stone on the commutator to promote full engagement between the brushes and commutator. 15. Install the motor cover. Page 12 Clarke American Sanders American B-2 Operator's Manual... - Page 13 NOTES Clarke American Sanders American B-2 Operator's Manual Page 13...
-
Page 14: Assembly Drawing #1
Model American B-2+ 7" Spinner Edger Drawing #1 11/04 12 13 Page 14 Clarke American Sanders American B-2 Operator's Manual... -
Page 15: Assembly Parts List #1
Note: Ref. #19 (19901A) includes ref #'s 17, 38, 39, 40 (2), & 41 NI = Not illustrated Note: Ref. #42 (12203A) includes ref #'s 17, 18, 38, 39, 40 (2), & 41. Clarke American Sanders American B-2 Operator's Manual Page 15... -
Page 16: Assembly Drawing #2
Model American B-2+ 7" Spinner Edger Drawing #2 11/04 Page 16 Clarke American Sanders American B-2 Operator's Manual... -
Page 17: Assembly Parts List #2
Relief - Strain 63701A Gear - Pinion 16091A Box - Switch 57701A Ring - Retaining 48800A Washer - Insulating 31408A Edger Case, B2 41001A Bushing - Insulating NI = Not illustrated Clarke American Sanders American B-2 Operator's Manual Page 17... -
Page 18: Wiring Diagram 3/93
Model American B-2 7" Spinner Edger Wiring Diagram 3/93 Page 18 Clarke American Sanders American B-2 Operator's Manual... - Page 19 29815 John R. Gilwilly Industrial Estate (810) 544-6300 Penrith Cumbria CA11 9BN ® American Lincoln / Clarke, Marietta, Georgia 30066 +44 1768 868 995 1455 Canton Road (770) 973-5225 ALTO France S.A. Strasbourg B.P. 44, 4 Place d’Ostwald F-67036 Strasbourg...
- Page 20 (b). Return the product to the nearest Clarke American Sanders repair location. Transportation charges to and from the repair location must be prepaid by the purchaser. (c). Clarke American Sanders will repair the product and or replace any defective parts without charge within a reasonable time after receipt of the product.