Page 1
WALK BEHIND SCRUBBER Operating Instructions (ENG) Instrucciones de funcionamiento (SPA) MODELS: SCX326 10052400 SCXN326 10052850 BSCSCX326 10052880 IPX4 Read these instructions before using the machine Lea las instrucciones antes de utilizar la máquina 86039100 01/20/12 PRV NO. 98966...
Warranty Registration Thank you for purchasing a Windsor product. Warranty registration is quick and easy. Your registration will allow us to serve you better over the lifetime of the product.
TABLE OF CONTENTS Machine Data Log/Overview......2 Brush Shrouds & Brush Skirts ....4-10 Table of Contents..........3 Vacuum Motor ...........4-11 Actuator Scrub Deck........4-12 HOW TO USE THIS MANUAL Machine Troubleshooting ......4-13 GROUP PARTS LIST How to use this Manual.........1-1 SAFETY Control Handle..........
They are Parts may be ordered from authorized Windsor listed in this general order: dealers. When placing an order for parts, the machine model and machine serial number are Batteries important.
IMPORTANT SAFETY INSTRUCTIONS When using an battery powered appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. WARNING: To reduce the risk of fire, electric shock, or injury: Use only indoors. Do not use outdoors or expose to rain. Use only as described in this manual.
WHEN SERVICING MACHINE: Avoid moving parts. Do not wear loose clothing; jackets, shirts, or sleeves when working on the machine. Use Windsor approved replacement parts. WARNING Batteries emit hydrogen gas. Explosion or fire can result. Keep sparks and open flame away. Keep top cover in raised position when charging.
SAFETY LABEL LOCATION NOTE: These drawings indicate the location of safety labels on the machine. If at any time the labels become illegible, promptly replace them. SAFETY DECAL 86252530 PRV NO. 81494 BATTERY CAUTION 86252520 PRV NO. 80885 SEE MANUAL CIRCUIT BREAKER DECAL 86243610 2% GRADE WARNING...
TECHNICAL SPECIFICATIONS ITEM DIMENSION/CAPACITY Nominal power 2160 W Rated Voltage 36 Volt DC Rated Amperage 60 amps Batteries 6 x 6 volt 250-305-335 AH @ 20 Hr rate Scrub Brush Motors 2 x .75 hp (.56 kW) Vacuum Motor 3 Stage .75 hp (.56 kW) Propelling Motor .75 hp (.56 kW) Mass (GVW)
Page 9
TECHNICAL SPECIFICATIONS ITEM MEASURE Height 46 in (117 cm) Length with 32 in. (81 cm) scrub head 71 in (180) Width without squeegee and scrub head 28 in (71 cm) Width of squeegee for 32 in. (81 cm) scrub head 39 in (99 cm) Width of scrub path for 32 in.
HOW THE MACHINE WORKS The Saber Cutter is a battery powered, self- propelled, hard floor scrubber intended for The function of the recovery system is to vacuum commercial use. The appliance applies a the soiled water back into the recovery tank. The cleaning solution onto a hard floor, scrubs the recovery system consists of the squeegee, floor with brushes, and then vacuums the soiled...
COMPONENTS 1. Control Panel 2. Front Cover 3. Recovery Tank 4. Recovery Tank Drain Hose 5. Scrub Head Shrouds 6. Solution Tank 7. Solution Tank Cover 8. Solution Tank Drain Hose 9. Solution Strainer 10. Squeegee 11. Aqua-Mizer 12. Top Cover 13.
Page 13
CONTROLS 1. Key Switch 9. Vacuum Switch 2. Emergency Shut Off Switch (Optional) 10. Squeegee Lift Lever 3. Speed Control Knob 11. Squeegee Pitch Adjustment Knob 4. Propel Control Lever 12. Squeegee Deflection Adjustment Knobs 5. Reverse Button 13. Battery Charge Level Indicator 6.
Page 14
CONTROLS 10. SQUEEGEE LIFT LEVER 7. ACTUATOR SWITCH Raises and lowers the squeegee. Adjusts the amount of brush pressure to the floor by To lower the squeegee, lift the lever raising or lowering the scrub deck. from its raised position. To increase brush pressure, press the bottom of the To raise the squeegee, lift the lever from switch.
Page 15
CONTROLS 13. BATTERY CHARGE LEVEL INDICATOR Indicates the charge level of the batteries. The meter display is divided into 10 vertical bars. Bar illuminated on the far right indicate full charge. Bars flashing near the left side indicate the batteries should be recharged. Further operation of the machine could damage the machine or the batteries.
MACHINE OPERATION FILLING SOLUTION TANK PRE-RUN MACHINE INSPECTION FOR SAFETY: Before leaving or servicing Do a pre-run inspection to find possible problems that machine; stop on level surface, turn off machine could cause poor performance or lost time from and remove key. breakdown.
MACHINE OPERATION NORMAL SCRUBBING TO BEGIN SCRUBBING Plan the scrubbing pattern in advance. The WARNING longest track is around the perimeter of the area to be cleaned. For efficient operation, the runs When operating the machine around people, pay close attention for unexpected movement. Use should be the longest possible without turning, extra caution around children.
MACHINE OPERATION DOUBLE SCRUB RECOVERY TANK 1. Unhook the large drain hose from the retainer. For floors which are heavily soiled or have thick Unscrew the T-handle on plug enough to loosen accumulations of floor finish may not clean plug, then lower hose in direction of the drain. sufficiently with one pass.
MAINTENANCE SERVICE SCHEDULE MAINTENANCE DAILY WEEKLY MONTHLY Check batteries after charging; add water if necessary Check pad wear to prevent buildup of chemicals Check linkages and connectors for wear and damage Check hoses for wear, blockages, or damage Clean squeegee; check for adjustment; inspect for wear Check handles, switches, knobs, domes, and gaskets for damage...
Page 20
MAINTENANCE 1. Batteries 2. Squeegee 3. Aqua Mizer 4. Scrub Brushes 5. Recovery Tank Float Shut-Off 6. Solution Strainer 7. Brush Motor 8. Traction Motor 9. Circuit Breakers 10. Brush Shroud & Brush Skirts 11. Vacuum Motor 12. Actuator Scrub Deck CUTTER 36V 86039100 05/01/07...
MAINTENANCE 1. BATTERIES The batteries provide the power to operate the CAUTION machine. The batteries require regular maintenance When servicing machine, avoid contact with to keep them operating at peak efficiency. battery acid. The machine batteries will hold their charge for long WARNING periods of time, but they can only be charged a Batteries emit hydrogen gas.
MAINTENANCE CHECKING BATTERY SPECIFIC GRAVITY TO CHARGE THE BATTERIES Use a hydrometer to check the battery specific WARNING gravity. When servicing machine, avoid contact with battery acid. CAUTION Battery Check Batteries emit hydrogen gas. Explosion or fire can result. Keep sparks and open flame away. Keep covers open when charging.
MAINTENANCE 5. Replace the battery caps, and leave them in CHANGING BATTERIES place while charging. Stop the machine in a clean area next to the 6. Unplug the battery connector from the machine. charger. Turn off machine. FOR SAFETY: When charging, connect the FOR SAFETY: Before leaving or servicing the charger to the batteries before connecting the machine;...
MAINTENANCE 2. SQUEEGEE BLADES TO REMOVE SQUEEGEE ASSEMBLY The front squeegee blade allows solution to pass 1. With the squeegee in the up position, turn key through channels in the blade into the squeegee switch “OFF”. assembly while maintaining vacuum to provide lift. 2.
Page 25
MAINTENANCE TO ADJUST SQUEEGEE PITCH TO ADJUST AMOUNT OF REAR SQUEEGEE DEFLECTION 1. Choose a smooth, level surface. Turn “ON” the key switch. Lower the squeegee and drive 1. Choose a smooth, level surface. Lower the forward at least 2 feet (60cm.). squeegee and drive forward at least 2 feet 2.
MAINTENANCE SCRUB BRUSHES REPLACING OR INSTALLING SCRUB BRUSHES There are four different types of brushes available to cover applications from cleaning heavily soiled floors 1. With the scrub deck up, turn “OFF” the machine. to polishing. A pad driver is also available to take advantage of the many cleaning pads on the market.
MAINTENANCE 6. SOLUTION STRAINER 8. Reset end cap and realign with scribe marks on motor barrel. Reinstall the two attach bolts from The solution strainer is located in front of the left cap into base. front wheel. The solution strainer protects the 9.
MAINTENANCE TRACTION MOTOR CIRCUIT BREAKERS Circuit breakers interrupt the flow of power in WARNING the event of an electrical overload. When a Do not use a pressure washer to clean around the circuit breaker is tripped, reset it by pressing motors.
4. Loosen clamp and disconnect hose from vacuum intake. 5. Remove vacuum motor mounting bracket bolts. 6. Remove vacuum motor from mounting bracket. 7. Reverse steps to install. Note: Vacuum Motor Carbon Brushes Replacement (Windsor) Place End Cap stop in groove. Carbon...
MAINTENANCE 12. ACTUATOR SCRUB DECK SCRUB DECK ACTUATOR ADJUSTMENT REMOVAL/REPLACEMENT The actuator will need to be adjusted when replaced. FOR SAFETY: Before leaving or servicing To adjust the actuator: machine, stop on a level surface, turn off machine and set parking brake (If option is 1.
MACHINE TROUBLESHOOTING PROBLEM CAUSE SOLUTION Poor or no water pick-up Squeegee out of adjustment Adjust squeegee Debris caught on squeegee Remove debris Worn squeegee blades Rotate or replace squeegee blades Vacuum hose clogged Clear obstruction from hose Vacuum hose disconnected Reconnect vacuum hose from squeegee or recovery tank...
Page 32
MACHINE TROUBLESHOOTING PROBLEM CAUSE SOLUTION Little or no solution flow to the floor Solution tank empty Fill solution tank Solution flow turned off or Turn on or increase flow set too low setting Solution strainer plugged Clean solution strainer Solution hoses obstructed Clear obstruction from hose Solution solenoid valve...
Page 33
THIS PAGE LEFT BLANK INTENTIONALLY 4-15 CUTTER 36V 86039100 05/01/07...
COVER (FRONT) & TANK MOUNT CUTTER 36V 86039100 05/12/08...
Page 37
COVER (FRONT) & TANK MOUNT SERIAL REF PART NO. PRV NO. QTY DESCRIPTION NOTES: NO. FROM 86073690 140576 BRACKET, REC TO SOL W/BRAKE 36V 86010670 87029 WASHER, 5/16 FLAT SS 86276780 70728 SCR, 5/16-18 X 3/4 HHCS SS 86062550 27927 COVER, FRONT 36V GRY 86004790 48012...
COVER (TOP) & TANK MOUNT CUTTER 36V 86039100 05/01/07...
Page 39
COVER (TOP) & TANK MOUNT SERIAL NO. PART NO. PRV NO. DESCRIPTION FROM NOTES: 86062560 27928 COVER, TOP 36V GRY 86271840 57285 NUT, 5/16-18 HEX NYLOCK THIN SS 86010670 87029 10 WASHER, 5/16 FLAT SS 86239650 41432 HINGE, COVER TO TANK 86276780 70728 SCR, 5/16-18 X 3/4 HHCS SS...
Page 45
LIFT HANDLE SERIAL NO. PART NO. PRV NO. DESCRIPTION FROM NOTES: 86082910 66376 PLATE, LEVER NOTCH DELUXE 36V 86010670 87029 WASHER, 5/16 FLAT SS 86276780 70728 SCR, 516-18 X 3/4 HHCS SS 86066860 140537 BAR, SQG LIFT SWING 36V 86006930 70514 SCR, 5/16-18 X 1.00 BSHCS SS 86238360...
Page 53
SCRUB DECK AQUA-MIZER SERIAL NO. PART NO. PRV NO. DESCRIPTION FROM NOTES: 86006930 70514 SCR, 5/16-18 X 1.00 BSHCS SS 86228840 09124 BEARING, FLANGED .314 ID X .502 OD 86259420 87232 WASHER, THRUST .51 ID X 1 OD BRO 86259400 87205 WASHER, THRUST .51 ID X 1 OD BRO 86255060...
Page 59
SCRUB DECK LIFT LINKAGE SERIAL NO. PART NO. PRV NO. DESCRIPTION FROM NOTES: 86069860 140530 BRKT, CENTER LINK 36V 86228840 09124 BEARING, FLANGED .314 ID X .502 OD 86259400 87205 WASHER, THRUST .51 ID X 1 OD BRO 86271840 57285 NUT, 5/16-18 HEX NYLOCK THIN SS 86010670 87029...
Page 61
SCRUB DECK LIFT LINKAGE SERIAL NO. PART NO. PRV NO. DESCRIPTION FROM NOTES: 86273780 70015 SCR, 1/4-20 X 3/4 HHCS SS NP 86070030 140561 BRKT, ANGLE SUPPORT 36V 86010630 87013 WASHER, 1/4 ID X 5/8 OD SS 86273740 70010 SCR, 1/4-20 X 1.5 HHCS 86271870 57290 1/4-20 HEX NYLOCK THIN SS...
Page 73
53799 VAC MOTOR ASM, 36VDC 3 STAGE 86230800 140550 BRUSH SET, VAC MOTOR AMETEK SERVICE ONLY 86135310 140686 BRUSH SET, VAC 24V/36V WINDSOR SERVICE ONLY 86010630 87013 WASHER, 1/4ID X 5/8OD SS 86273810 70018 SCR, 1/4-20 X 1 HHCS SS...
Page 77
WIRING-BATTERY SERIAL NO. PART NO. PRV NO. DESCRIPTION FROM NOTES: 86008760 80682 CONNECTOR, BATTERY GRY, 175AMP 86271870 57290 NUT, 1/4-20 HEX NYLOCK THIN SS 86271910 57295 NUT, 5/16-18 FLEXLOCK 86008920 80889 BOOT, RUBBER TERM. ISOLATOR 86009000 81131 WIRE, 4 X 9.5 BK 5/16 RING X 5/16 RING 86010850 880352 WIRE, 4X20 RD C, TERM X 5/16 RING...
Page 78
WIRING GROUP – CONTROL PANEL DIAGRAM B DIAGRAM A 51 RED 30 RED 49 BLK 56 RED 18 BLU 48 BLK 47 RED 52 RED 41 BLU 29 YLW 50 BLK 43 BLK 63 BLK 62 RED 63 BLK 26 RED 61 BLK 33 RED 2/25 BLK...
Page 79
WIRING GROUP – CONTROL PANEL SERIAL REF PART NO. PRV NO. QTY DESCRIPTION NO. FROM NOTES: 86238990 41442 HARNESS, PANEL, DELUXE 86261210 29204 DIODE ASM, 76008 X 76008 86003410 29215 DIODE ASM, 76075 X 76075 86267340 880269 WIRE, 22” RED/18 76040 X 76075 86269300 88868 WIRE, 16”...
Page 80
WIRING GROUP – MAIN HARNESS 74 RED RIGHT BRUSH MOTOR 75 BLK 76 RED LEFT BRUSH MOTOR 77 BLK 72 RED MOTOR 73 BLK 5 BRN DIAGRAM A 73 BLK 6 BLK 75 BLK 78 RED ACTUATOR 79 BLK 76 RED 72 RED 69 RED 77 BLK...
Page 81
WIRING GROUP – MAIN HARNESS SERIAL NO. PART NO. PRV NO. DESCRIPTION FROM NOTES: 86238980 41441 HARNESS, MAIN 86260400 880212 WIRE ASM, REV POLARITY JUMPER SERVICE ONLY CUTTER 36V 86039100 05/01/07 5-48...
Page 85
BRAKE-OPTION SERIAL NO. PART NO. PRV NO. DESCRIPTION FROM NOTES: 86248370 66381 PAD, BRAKE 86006220 66192 PIN, ROLL 1/4 X 1.25L 86251800 67485 ROD, BRAKE 36V 86231330 14664 BUSH, BRZ FLG .63 X .75 X 1.0 86255060 73426 SPRING, EXT .43D X 2.50 L X .047 W 86070060 140564 BRKT, LOWER BRAKE MOUNT 36V...