Page 1
All manuals and user guides at all-guides.com NSX-R50 NSX-R51 SERVICE MANUAL COMPACT DISC BASIC TAPE MECHANISM : ZZM-3 PR3NM STEREO SYSTEM BASIC CD MECHANISM : BZG-5 ZD3GNM REMOTE SYSTEM SPEAKER CASSEIVER CONTROLLER NSX-R50 CX-NR50 SX-NR50 RC-CAS01 NSX-R51 CX-NR51 • If requiring information about the CD mechanism, see Service Manual of BZG-5, (S/M Code No.
All manuals and user guides at all-guides.com SPECIFICATIONS MAIN UNIT CX-NR50 (K) / CX-NR51 (EZ) CD PLAYER TUNER Laser λ FM tuning range D/A converter FM usable sensitivity (IHF) Signal-to-noise ratio FM antenna terminal Harmonic distortion MW tuning range GENERAL µ...
All manuals and user guides at all-guides.com PROTECTION OF EYES FROM LASER BEAM DURING SERVICING CAUTION This set employs laser. Therefore, be sure to follow carefully the instructions below when servicing. Use of controls or adjustments or performance of proce- dures other than those specified herin may result in WARNING!! hazardous radiation exposure.
All manuals and user guides at all-guides.com NOTE ON BEFORE STARTING REPAIR 1. Forced discharge of electrolytic capacitor of power supply block When repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged across the electrolytic capacitors (C101, 102) even though AC power cord is removed.
Page 5
All manuals and user guides at all-guides.com In such a case, check also if the POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not. 2-2. Regarding reset There are cases that the machine does not work correctly because the MICROCOMPUTER is not reset even though the AC power cord is re-inserted, or the software reset (pressing the STOP key + POWER key) is performed.
All manuals and user guides at all-guides.com ELECTRICAL MAIN PARTS LIST REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION 87-A12-826-000 CAP,E 3300-35 M 85 GS 87-A12-826-000 CAP,E 3300-35 M 85 GS 87-A21-419-040 C-IC,NJM14558MD-TE2 87-A12-072-080 CAP,E 100-25 SMG 87-A22-112-040 C-IC,BD3861FS 87-A12-072-080...
Page 7
All manuals and user guides at all-guides.com REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION C403 87-012-193-080 C-CAP,U 82P-50 CH C793 87-A12-090-080 CAP,E 4.7-50 SMG C404 87-012-193-080 C-CAP,U 82P-50 CH C795 87-012-286-080 CAP, U 0.01-25 C405 87-012-286-080 CAP, U 0.01-25 C796...
Page 8
All manuals and user guides at all-guides.com REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION C942 87-012-165-080 CAP 3P R995 87-012-195-080 C-CAP,U 100P-50CH C947 87-012-286-080 CAP, U 0.01-25 SFR451 87-A90-432-080 SFR,30K H NVZ6TLTA C948 87-A10-039-080 C-CAP,U 470P-50 J CH SFR452 87-A90-432-080 SFR,30K H NVZ6TLTA...
All manuals and user guides at all-guides.com TRANSISTOR ILLUSTRATION E C B E C B G D S B C E 2SB1370 2SC2240(GR/BL) 2SA1980G 2SK3053 2SA1981Y CDA1585BC CSC4115BC KTC3198GR B C E S D G 2SB1686 2SA1235F 2SJ460 2SK360E KRA102S 2SC2620B 2SD2642 2SK2541...
Page 11
All manuals and user guides at all-guides.com WIRING – 1 (MAIN / HP) – 11 –...
Page 12
All manuals and user guides at all-guides.com SCHEMATIC DIAGRAM – 1 (MAIN 1 / 2) – 12 –...
Page 13
All manuals and user guides at all-guides.com SCHEMATIC DIAGRAM – 2 (MAIN 2 / 2 : TUNER) – 13 –...
All manuals and user guides at all-guides.com IC BLOCK DIAGRAM – 20 –...
Page 21
All manuals and user guides at all-guides.com – 21 –...
Page 22
All manuals and user guides at all-guides.com FL (BJ854GNK BNF 1) GRID ASSIGNMENT / ANODE CONNECTION GRID ASSIGNMENT ANODE CONNECTION 22 ...
Page 23
All manuals and user guides at all-guides.com IC DESCRIPTION PD780228-061-3BA µ Pin Name Pin No. Description O-MOTOR DECK MOTOR ON/OFF output. O-SOL1 DECK1 solenoid ON/OFF output. O-SOL2 DECK2 solenoid ON/OFF output. O-LED_STB STB signal make clock and data effective. O-MUTE System MUTE ON/OFF output.
Page 24
All manuals and user guides at all-guides.com Pin Name Description Pin No. I-SPEANA_1 A/D input for spectrum analyser level display. I-SPEANA_2 A/D input for spectrum analyser level display. I-SPEANA_3 A/D input for spectrum analyser level display. I-KEY 1 Key A/D input 1. I-KEY 2 Key A/D input 2.
Page 25
All manuals and user guides at all-guides.com ADJUSTMENT (TUNER / DECK / FRONT) A MAIN C.B PARTS SIDE TC942 L941 L802 L951 L942 SFR451SFR452 L901 L902 A MAIN C.B PATTERN SIDE IC801 SFR452SFR451 R962 RPH/PH G DECK C.B SFR1 25 ...
Page 26
All manuals and user guides at all-guides.com <TUNER Adjustment> 1. VT Adjustment and Check (LW) Requirements Measuring instrument: Digital multimeter Test point: VT, GND Adjustment point: L942 (1) Connect a digital multimeter to VT and GND. DIGITAL MULTIMETER (2) Set the unit function to LW, and adjust the receiving frequency at 144 kHz. (3) Adjust L942 so that the digital multimeter indicates 1.3 ±...
Page 27
All manuals and user guides at all-guides.com <MW/LW Adjustment> Make sure that the following settings are done before adjustment. Preparation Measuring instruments: Standard Signal Generator (S.S.G.) / Loop antenna / Oscilloscope / Millivoltmeter / Dummy resistor (6Ω) (1) Connect the measuring instruments as shown in the diagram below. (2) Keep a distance of 60cm between the loop antenna of signal generator and the one connected to the unit.
Page 28
All manuals and user guides at all-guides.com <FM Adjustment> Make sure that the following settings are done before adjustment. Preparation * Measuring instruments: Standard Signal Generator (S.S.G.) / Oscilloscope / Millivoltmeter / Dummy resistor (6Ω) (1) Connect the measuring instruments as shown in the diagram below. (2) Connect the output terminal of signal generator to the antenna input terminal of the unit.
Page 29
All manuals and user guides at all-guides.com <Deck Section> 12. Tape Speed Adjustment (DECK 2) Requirements Measuring instruments: Wow-flutter meter (frequency counter) Test tape: TTA-100 (3 kHz) Test point: HP OUT WOW&FLUTTER METER Adjustment point: SFR1 (1) Connect the HP OUT terminal of the unit to the wow-flutter meter. INPUT (2) Insert the test tape (TTA-100) to DECK 2.
Page 30
All manuals and user guides at all-guides.com 17. Playback Sensitivity Check (DECK 1, DECK 2) Requirements Measuring instrument: Millivoltmeter Test tape: TTA-200 (400 Hz) Test point: TP8 (Lch), TP9 (Rch) (1) Connect the CH1 of millivoltmeter to TP8 (Lch) and the CH2 to TP9 (Rch). (2) Insert the test tape (TTA-200) to DECK 1 to playback.
Page 31
All manuals and user guides at all-guides.com <Front Section> B FRONT C.B PATTERN SIDE CLOCK B FRONT C.B PARTS SIDE L951 FREQUENCY COUNTER 20. Clock Adjustment Requirement CLOCK Measuring instrument: Frequency counter Test point: CLOCK, GND (1) While pressing and holding down the POWER button and the UP button, insert the AC plug. (2) Adjust L951 so that the frequency counter indicates 84.804 ±...
All manuals and user guides at all-guides.com CD TEST MODE 1. Starting CD Test Mode Insert the AC plug while pressing and holding down the CD OPEN/CLOSE button. When the test mode is activated, the display appears TEST. 2. Exiting CD Test Mode Press the POWER button or unplug the AC plug.
All manuals and user guides at all-guides.com GENERAL SPEAKER DISASSEMBLY INSTRUCTIONS (FOR REFERENCE) Type.1 Type.4 Insert a flat-bladed screwdriver into the position indicated by the TOOLS arrows and remove the panel. Remove the screws of each speaker 1 Plastic head hammer unit and then remove the speaker units.
All manuals and user guides at all-guides.com SPEAKER PARTS LIST SX-NR50 (YSL) REF. NO. PART NO. KANRI DESCRIPTION 1 8B-NSA-001-010 PANEL,FR R 2 8B-NSA-002-010 PANEL,FR L 3 8B-NSA-003-010 PANEL,BA R 4 8B-NSA-004-010 PANEL,BA L 5 8B-NSA-005-010 GRILLE,FRAME ASSY 6 8B-NSA-602-010 SPKR, W 160 30/4 7 8B-NSK-604-010 SPKR, T 60...
Page 39
All manuals and user guides at all-guides.com 2–11, IKENOHATA 1–CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:03 (3827) 3111 9301978 9720501 921338 Printed in Singapore...