Fanimation Belleria FP4320 Series Owner's Manual
Wet location model
Hide thumbs
Also See for Belleria FP4320 Series:
- Specification sheet (2 pages) ,
- Owner's manual (14 pages)
Related Manuals for Fanimation Belleria FP4320 Series
Summary of Contents for Fanimation Belleria FP4320 Series
-
Page 1: Ceiling Fan
The Belleria ® Ceiling Fan Wet Location Model Net Weight 9.9 kg (21.78 lbs) Model No. FP4320** OWNER’S MANUAL READ AND SAVE THESE INSTRUCTIONS... -
Page 2: Table Of Contents
Fanimation. 7. Fanimation reserves the right to modify or discontinue any product at any time and may substitute any part under this warranty. 8. Under no circumstances may a fan be returned without prior authorization from Fanimation. The receipt of purchase must ac- company authorized returns and must be sent freight prepaid to Fanimation. -
Page 3: Unpacking Instructions
Fanimation. Substitution of parts or accessories not designated for use with this product by Fanimation could result in personal injury or property damage. Contact your retail store for missing or damaged parts. -
Page 4: Electrical And Structural Requirements
Electrical and Structural Requirements Your new ceiling fan will require a grounded electrical supply line of 120 volts AC, 60 Hz, 15 amp circuit. The outlet box must be securely anchored and capable of withstanding a load of at least 50 lbs. Figure 1 depicts different structural configurations that may be used for mounting the outlet box. - Page 5 How to Assemble Your Ceiling Fan (cont’d) NOTE: You will be using either the 6˝ downrod supplied with your fan or an optional downrod purchased seperately. 4. Loosen the two setscrews and hex nuts in the Downrod Support. Screw Downrod into Coupler. Align the Clevis Screw holes in the Downrod with the holes in the Downrod Support.
-
Page 6: How To Hang Your Ceiling Fan
▲WARNING To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before hanging. NOTE: If you are not sure if the outlet box is grounded, contact a licensed electrician for advice, as it must be grounded for safe operation. -
Page 7: How To Wire Your Ceiling Fan - Pull Chain
How to Wire Your Ceiling Fan - Pull Chain If you feel that you do not have enough electrical wiring knowledge or experience, have your fan installed by a licensed electrician. ▲WARNING To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring. -
Page 8: Installing The Canopy Housing
Installing the Canopy Housing NOTE: This step is applicable after the neccessary wiring is completed. (see page 7) ▲WARNING To avoid possible fire or shock, make sure that the electrical wires are completely inside the canopy housing and not pinched between the housing and the ceiling. 1. -
Page 9: Maintenance
Mounting the Fan Blades (cont’d) 8. Attach Blade Holders to the bottom of the Fan Motor Hub using the ¼–20 x ⅝˝ Socket Head Screws w/Lockwashers as shown in Figure 3. 9. Make sure the screws with lockwashers securing the Blade Holders to the Fan Motor Hub are tight and that the Blade Holders are properly seated. -
Page 10: Parts List
Before discarding packaging materials, be certain all parts have been removed When ordering repair parts, always give the following information: Contact your retail store for repair parts. Parts List Model #FP4320** Description –24 x 10 mm˝ (11) How To Order Parts • Part Number •... -
Page 11: Exploded-View Drawing
The Belleria FP4320** ® Exploded-View NOTE: The illustration shown is not to scale or its actual confi guration may vary Figure 1 Ground Wire (Green) -
Page 12: Trouble Shooting
For your own safety turn off power at fuse box or circuit breaker before trouble shooting your fan. Trouble 1. FAN WILL NOT START 1. Fuse or circuit breaker blown. 2. Loose power line connections to the fan, or loose switch wire connections in the switch housing. - Page 14 10983 Bennett Parkway Zionsville, IN 46077 (888) 567-2055 FAX (866) 482-5215 Outside U.S. call (317) 733-4113 Visit Our Website @ www.fanimation.com Copyright 2007 Fanimation 2007/10...