Advertisement
Interface Description/ 接口说明
IPC6625-Z30-S
IPC6625-Z30-P
NOTE/ 说明
The color identifier of the alarm cable is subject to the actual pigtail label.
告警线缆颜色标识以实际的尾线标签为准。
NO.
Item
Description
序号
名称
说明
Indicates the power input interface that supports 24 V AC (18.0 V to 29.9 V) and 24 V DC (19.2
1
POWER
V to 28.8 V) power input.
电源输入接口。支持AC 24V（18.0V～29.9V）和DC 24V（19.2V～28.8V）电源输入。
Indicates the network interface used to connect to network cables.
2
LAN
网络接口。连接网线。
Indicates the network interface used to connect to network cables.
PoE++ is supported, with a maximum power consumption of 60 W.
3
LAN/POE++
网络接口。连接网线。
PoE++供电接口。支持PoE++供电。供电最大功耗60W。
GND
Indicates the ground interface.
4
接地线
接地接口。
ALARM_OUT Indicates the alarm output interface. ALARM_OUT and ALARM_REF form a group of alarm
output.
告警输出接口。ALARM_OUT和ALARM_REF组成一组告警输出。
ALARM_REF
Indicates the alarm input ground interface.
5
GND
告警输入接地接口。
Indicates the alarm input interface. The value m is an integer ranging from 0 to 3. ALARM_INm
and GND form a group of alarm input. There are four groups of alarm input.
ALARM_INm
告警输入接口，m为0～3之间的整数。ALARM_INm和GND组成一组告警输入，一共4组。
NOTE/ 说明
After a PoE++ device is connected to the power supply device, if power cannot be supplied, check whether either
of the following problems exists on the power supply device:
The network port of the power supply device is a power port of a non-Huawei PoE++ device.
The total power consumption of the power supply device does not meet requirements.
POE++ 设备连接到供电设备，出现无法供电的情况，建议排查供电设备是否存在以下问题：
供电设备网口为非华为 POE++ 设备供电口
供电设备合计供电功率不满足要求
Reset button and SD card slot/Reset 键和 SD 卡槽
1
1
2
2
4
5
3
4
NO.
Operation
Description
5
序号
操作
说明
Reset button. To restart the device, hold down the RST button for less than 3s. To restore
the device to factory defaults, hold down the RST button for at least 3s during the device
Use a Phillips
running or hold down the RST button, power on the device, and keep holding down the
1
RST button for more than 5s.
screwdriver to
重置按钮。运行时按住RST键短于3秒重启设备；运行时按住RST键不短于3秒或者按住RST键后上
remove the left ear
电并持续按住RST键不短于5秒后恢复出厂配置。
cover. Then, you can
SD card slot that supports only Micro SD cards of Class 6 or higher classes. You can
see the Reset button
replace a Micro SD card only when the device is powered off. When a Micro SD card is
and SD card slot.
used for the first time, log in to the web page of the device and format the Micro SD
使用十字螺丝刀将球机
2
card. For details, see Configuration Guide.
左耳盖卸下，即可看到
SD卡卡槽，仅支持Micro SD卡（Class 6及以上）。请在设备断电的情况下插拔SD卡，否则会
重置键和 SD 卡槽。
造成系统异常。首次使用时，请登录设备Web客户端，格式化SD卡，操作方法请参见《配置指
南》。
Prepare for Installation Tools/ 准备安装工具
PVC insulation tape
绝缘胶带
Marker
记号笔
Socket wrench (M6)
套筒扳手（M6）
Phillips screwdriver (Head model:
0#.)
十字螺丝刀（刀头型号为：0#）
NOTE/ 说明
Before deliver y, a 32G SD card has
been inserted into the SD card slot of
the camera. Please refer to "Install the
Device>Install the SD card" if the SD
HUAWEI
card needed to be changed.(6625-Z30-S
does not support.)
出厂时，本机自带32G SD卡并已插入SD卡
卡槽。如需更换SD卡，请参见"设备安装>
安装SD卡"。（6625-Z30-S不支持。）
Wiring terminal
接线端子
Hammer drill (for mounting a
Claw hammer (for mounting a camera
camera on the ceiling or wall)
on the ceiling or wall)
冲击钻（吊顶和墙壁安装时使用）
羊角锤（吊顶和墙壁安装时使用）
Cable stripper
RJ-45 connector crimping tool
剥线钳
Glass cement
玻璃胶
Measuring tape
钢卷尺
水晶头压线钳
Waterproof tape
防水胶带
Advertisement
