Break-In Period - AEG BAC218E Original Instructions Manual

WARNING
Always wear eye protection with side shields. Failure to do so
could result in objects being thrown into your eyes, resulting in
possible serious injury.
WARNING
Do not use any attachments or accessories not recommended
by the manufacturer of the product. The use of attachments or
accessories not recommended can result in serious personal
injury.
WARNING
This equipment incorporates parts, such as snap switches,
receptacles, and the like that tend to produce arcs or sparks and,
therefore, when located in a garage, it should be in a room or
enclosure provided for the purpose, or should be 45 cm or more
WARNING
Do not attach any tools to the open end of the hose until start-up
has been completed.
WARNING
Always remove battery packs from the tool when you are
assembling parts, making adjustments, cleaning, or when not in
use. Removing battery packs will prevent accidental starting that
could cause serious personal injury.
WARNING
Do not use in an environment that is dusty or otherwise
contaminated. Using the air compressor in this type of
environment may cause damage to the unit.
APPLICATIONS
Air compressors are utilized in a variety of air system applications.
Match hoses, connectors, air tools, and accessories to the
capabilities of the air compressor.
You may use this product for the purposes listed below:
Operating light- to medium-duty air-powered tools
Operating air accessories such as air nozzles and automotive
tire inflators
INSTALLING/REMOVING BATTERY PACKS
See Figure 1.
The compressor can run with one or two battery packs.
NOTE: For best performance, install two fully-charged battery
packs before beginning operation. Minimum recommended battery
capacity is 4.0 Ah per battery pack.
Make sure the air compressor is turned off.
Insert each battery pack into the product as shown.
Make sure the latches on each side of the battery pack snap
into place and the battery pack is secured in the product before
beginning operation.
Depress the latches to remove the battery pack.
For complete charging instructions, see the operator's manuals for
your battery pack and charger.
8
CONNECTING/DISCONNECTING AIR HOSE (HOSE NOT
PROVIDED)
See Figure 2.
Never exceed the air tool's pressure rating as recommended by
Make sure the air compressor is turned off and the battery
packs are not installed.
Rotate pressure regulator knob fully in the counter-clockwise
direction so that the outlet pressure is at zero bar (0 psi).
Attach hose with quick connect air fitting to 1/4 in. quick coupler
on air compressor. Make sure to push the hose adapter end
fully into the coupler until the sleeve springs forward to lock it
in place.
To disconnect an air hose or an air tool:
Confirm that the outlet pressure is at zero bar (0 psi).
When disconnecting a hose from 1/4-in. quick coupler, always
firmly hold release end of hose.
Pull back on the release sleeve on the 1/4-in. quick coupler.
With a firm grip, pull out the quick-connect air fitting that is
attached to the quick coupler.

BREAK-IN PERIOD

the air compressor at zero tank pressure with the drain valve fully
open for 30 minutes or until both battery packs are completely
TURNING THE AIR COMPRESSOR ON/OFF
See Figure 3.
Install the battery packs.
Move the Auto On/Off switch to the AUTO ON (I) position to
power the compressor on.
To turn the air compressor off, move the Auto On/Off switch to
the OFF (O) position.
NOTE: When the compressor is in the AUTO ON (I) position, the
air compressor will automatically turn back on when the designated
tank air pressure drops below the preset pressure limit. It will also
shut off again when the cut-off pressure is reached.
Never exceed the air tool's pressure rating as recommended by
Always ensure the switch is in the OFF (O) position and the
regulator pressure gauge reads zero before changing air tools or
disconnecting the hose from the air outlet. Failure to do so could
result in possible serious personal injury.
USING THE AIR COMPRESSOR
See gure .
8
WARNING
WARNING
WARNING