Related Manuals for MachineryHouse Hafco Metalmaster SRG-12
Summary of Contents for MachineryHouse Hafco Metalmaster SRG-12
- Page 1 OPERATION MANUAL Model. SRG-12 Order Code S267 Edition No : SRG-12-1 Date of Issue : 05/2021...
-
Page 2: Machine Details
SRG-12 SERIAL NO. DATE OF MANF. istributeD by www.machineryhouse.co.nz NOTE: This manual is only for your reference. Owing to the continuous improvement of the Hafco Metalmaster machine, changes may be made at any time without obligation or notice. Please ensure the local voltage is the same as listed on the specification plate before operating this electric machine. -
Page 3: Specification
OPERATION MANUAL SPECIFICATION Order Code S267 MODEL SRG-12 Useful Length (mm) Capacity - Mild Steel (mm) Roll Diameter (mm) Includes Stand (Yes/ No) Wire Groove Positions (No) Dimensions (L x W x H) (cm) 75 x 19.5 x 39.3 Shipping Dimensions (L x W x H) (cm) 42.5 x 18 x 20.5 Nett Weight (kg) 13.6... - Page 4 OPERATION MANUAL GENERAL MACHINE SHOP SAFETY WARNINGS AND PRECAUTIONS When using this tool, basic safety precautions should always be followed to reduce the risk of personal injury and damage. Read all instructions before using this tool ! 1. Keep the work area clean. Cluttered areas invite injuries. 2.
- Page 5 OPERATION MANUAL GENERAL MACHINE SHOP SAFETY WARNINGS AND PRECAUTIONS 15. Do not operate tool if under the influence of alcohol or drugs. Read warning labels if taking prescription medicine to determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not operate the tool. 16.
-
Page 6: Potential Hazards And Injuries
OPERATION MANUAL DO NOT use this machine unless you have been instructed in its safe use and operation and have read and understood this manual Safety glasses must be worn when Long and loose hair must be contained operating this equipment when operating this equipment. -
Page 7: Site Preparation
OPERATION MANUAL 4 SETUP UNPACKING This machine was carefully packaged for safe transport. When unpacking, separate all enclosed items from packaging materials and inspect them for shipping damage. If items are damaged, please contact your distributor. NOTE: Save all the packaging materials until you are completely satisfied with the machine and have resolved any issues with the distributor, or the shipping agent. -
Page 8: Operation
OPERATION MANUAL 5. OPERATION This machine may perform many types of operations that are beyond the scope of this manual. Many of these operations may be dangerous or deadly if performed incorrectly. The instructions in this section are written with the understanding that the operator has the necessary knowledge and skills to operate this machine. -
Page 9: How To Order Spare Parts
2. A scanned copy of your parts list/diagram with required spare part/s identified 3. Go to www.machineryhouse.com.au/contactus and fill out the enquiry form attaching a copy of scanned parts list. CONTENTS Spare Parts Diagram.......... -
Page 10: Spare Parts Diagram
OPERATION MANUAL SPARE PARTS DIAGRAM... -
Page 11: Spare Parts List
OPERATION MANUAL SPARE PARTS LIST ITEM DESCRIPTION QTY. ITEM DESCRIPTION QTY. ADJUSTMENT KNOB SPRING WASHER 8MM BASE GEAR GUIDE PLATE UPPER SHAFT ADJUSTMENT KNOB LOWER SHAFT LEFT STAND HANDLE BUSHING NUT M10 BOLT M8X35 HANDLE GRIP IDLE SHAFT SCREW M10X120 WASHER 8MM WASHER 6MM RIGHT STAND... - Page 12 General Machinery Safety Instructions Machinery House requires you to read this entire Manual before using this machine. 1. Read the entire Manual before starting 14. Use correct amperage extension cords. machinery. Machinery may cause serious injury if Undersized extension cords overheat and lose not correctly used.
- Page 13 Manual Sheetmetal Rolls Safety Instructions Machinery House requires you to read this entire Manual before using this machine. 1. Maintenance. 8. Work area hazards. Make sure all moving parts are Keep the area around the locked down before any inspection, adjustment or Rolling machine clean from oil, tools, chips.