Table of Contents
Advertisement
Quick Links
Installation, Operation and
Maintenance Manual
E-Treat
®
E-Treat
Salt-Free Scale
®
Prevention and Water Conditioning
System
Model ETREATWCS
WARNING
!
Read this Manual BEFORE using this equipment.
Failure to read and follow all safety and use information
can result in death, serious personal injury, property
damage, or damage to the equipment.
Keep this Manual for future reference.
WARNING
!
If you are unsure about installing your Watts E-Treat
contact a Watts representative or consult a professional plumber.
You are required to thoroughly read all installation instructions
and product safety information before beginning the installation
of this product. FAILURE TO COMPLY WITH PROPER
INSTALLATION AND MAINTENANCE INSTRUCTIONS
COULD RESULT IN PRODUCT FAILURE WHICH CAN CAUSE
PROPERTY DAMAGE, PERSONAL INJURY AND/OR DEATH.
Watts is not responsible for damages resulting from improper
installation and/or maintenance. Local building or plumbing codes
may require modifications to the information provided. You are
required to consult the local building and plumbing codes prior to
installation. If this information is not consistent with local building or
plumbing codes, the local codes should be followed.
Save manual for future reference.
Refer to the enclosed for operating parameters to ensure proper
use with your water supply.
• Use only lead-free solder and flux for sweat-solder connections,
as required by state, province and federal codes.
• Handle all components of the system with care. Do not drop,
drag or turn components upside down.
• Be sure the floor under the system is clean, level and strong
enough to support the E-Treat system while in operation.
• Install the system in a protected area.
• Do not attempt to treat water over 100°F (38°C) with the system.
• Always connect the system to the main water supply pipe before
the water heater.
• Do not expose the system to freezing temperatures. Water
freezing in the system causes equipment damage.
• Do not install in direct sunlight. Ultraviolet rays from the sun
may cause damage.
• Do not use on water that is microbiologically unsafe or of
unknown quality.
system
®
IOM-WQ-E-Treat
E-Treat
PN # 68101336
Advertisement
Table of Contents
Related Manuals for Watts E-Treat ETREATWCS
Summary of Contents for Watts E-Treat ETREATWCS
- Page 1 Keep this Manual for future reference. WARNING If you are unsure about installing your Watts E-Treat system ® contact a Watts representative or consult a professional plumber.
-
Page 2: Table Of Contents
The E-Treat system is a dual compartment tank based Watts E-Treat systems are complete, self-contained, system with 2 cubic feet of high capacity activated carbon which loaded with media and ready to use. A simple inlet and outlet reduces sediment, chlorine taste and odor, and integrated One- connection is all that is required for installation. -
Page 3: Feed Water Chemistry Requirements
4 weeks before placing NOTICE unit into service. For applications with copper concentra- tion greater than 1.3 ppm, please consult Watts Water Notes to the Installer Quality Technical Service. To further minimize any problem... -
Page 4: Installation Instructions
Installation Instructions The new system comes with the media, bypass, and tail pieces in the carton. Installer should verify this prior to installation. How to install your E-Treat system can also be found at www.PremierH2O.com. NOTICE Please confirm that all items required are included in the kit ready for assembly and remove from carton. -
Page 5: Maintenance
Maintenance Removing Carbon Media 1. Turn off water at supply valve or at main valve to home. 2. Open faucet in home to relieve pressure from E-Treat system, then place the system into the bypass position. Once placed in the bypass position, the main water supply valve can be turned to the ON position to restore water flow to the home. - Page 6 Removing OneFlow Media ® 1. Once the Carbon has been removed you can now insert the pipe as shown in Diagram A with the notched end over the dis- tributor tube and down into the tank as shown in Diagram B. 2.
- Page 7 Filling OneFlow Media ® 1. The 2.5" x 1.5" PVC coupling needs to be attached to the non-notched end of the 1.5" PVC pipe as shown in Diagram A. This keeps the pipe from falling into the tank. 2. With the distributor tube removed from the system, insert the pipe into the tank and through the center of the mid plate as shown in Diagram B.
- Page 8 Filling Carbon Media 1. Place tape over the top of the distributor tube to prevent Carbon from getting inside the distributor tube as shown in Diagram A. The tube should be completely covered as shown in Diagram B. 2. Put the blue media funnel into the top of the tank as shown in Diagram C.
-
Page 9: Media Replacement Tools
Media Replacement Tools Tools needed to replace E-Treat media that are not supplied by Watts: Standard wet/dry vacuum, and tape. Part No. 68110144 2.5" x 1.5" Reducing Coupling used to hold removal tube in place (keeps removal tube from falling into Part No. -
Page 10: Note To The Home Owner
Note To The Home Owner Things to watch for: During the first 30-90 days: Your E-Treat system will improve the properties of water through- out your home. Here are some things to expect and some rec- • Faucet aerators and drains may plug occasionally as old scale ommendations for maximizing the benefits and your enjoyment is removed from your plumbing system and water heater. -
Page 11: Limited Warranty
Limited Warranty • Watts Regulator Co. (the “Company”) warrants the E-Treat system is warranted to be free of defects in materials and workmanship for 5 years from the date of original shipment. Conditions 1. E-Treat systems are warranted for domestic use in residential single family dwelling applications excluding irrigation water treatment. The use of these systems in light commercial, commercial, or industrial applications will void their limited warranty.