Advertisement
Initial Operation
When the heater is initially connected to the mains the heater will power
up in MANUAL mode with a set temperature of 30˚C. The Mains and Heat
indication neon will be lit and the LCD display will be as per Fig.8. For
subsequent operations the unit will power up in its previous state, i.e. if it was
in the boost mode when the unit was plugged out when power is reinstated
it will resume in boost mode.
Setting the Time
To set the time press and hold ' ' for two seconds, the time digits will begin
flashing (Fig. 9). Press the '
ENTER to confirm. The heater will revert to the previous operational mode.
Standby Mode
With the heater ON, if the
button is pressed, the heater will go into standby
mode; the heater switches off, the LCD will display the current set time, only
the mains neon remains illuminated. On pressing the
heater will come on in Manual mode and with a set point setting of 25 ˚C.
Manual Operation
Repeatedly press the ' ' button until the manual mode is visible on the LCD
and confirm the mode selection by pressing ENTER. Use the arrow keys
to select the desired heat setting (see Operational modes for heat setting
details) and confirm the selection by pressing the ENTER key. The desired
temperature can be adjusted at any point during the Manual mode operation,
see Setting the Desired temperature.
Auto mode Operation
Repeatedly press the ' ' button until the Auto mode is visible on the LCD
(see Fig.10) and confirm the mode selection by pressing ENTER. The heater
will operate as per the pre-programmed time and temperature profile (see
- Setting the Timer Profile). Note: if no timer profile has been set it will not
be possible to select 'Auto' mode, it is necessary to set up a time program
before Auto mode can be selected.
During Auto mode operation the LCD display will show the current heat status,
the active programme segment, the time for the next status change, the heat
setting and the set temperature, see Fig.11 for details.
Heat status
Fig. 10
' or '
' buttons to set the time and press
Flashing
button again the
Time for next status
change (ON at 15:20)
Heat se ng
Set temperature
Ac ve segment
Boost mode Operation
Repeatedly press the ' ' button until the Boost mode is visible on the LCD
(see Fig.12) and confirm the mode selection by pressing ENTER. Once the
boost mode is activated it will be necessary select the boost period, there are
three periods available to choose from, 30 minutes, 1 hour and 2 hours. Use
the arrow keys to select the desired boost period and confirm the selection
using the ENTER key. The default heat setting is ECO mode and the set
temperature is 25˚C. The set temperature can be adjusted if desired, see
Setting the Desired temperature. When the boost mode is active the LCD
display will show the boost mode, timer period selected and the desired set
temperature. The time display will toggle between the current time and time
remaining for the selected boost period.
Fig. 8
Frost protection mode
The appliance has a frost protection mode. This setting is useful in areas
such as garages to assist in the prevention of frost damage. In Manual mode,
if the thermostat is set to its minimum setting '5°C', the heater will cycle ON
and OFF to maintain a temperature of approximately 5°C and help protect
against frosty conditions. The frost protection symbol
the LCD display when frost protection mode is activated.
Indicator Neons
Mains On Neon: The mains neon, (see Fig. 5), remains illuminated when
Fig. 9
the power is supplied to the product. Note: This does not indicate whether
the heating elements are on.
Heat Neon: Heat neon remains on when the heating element is active. Once
the desired temperature is reached and the element turns off, the heat neon
will indicate this by remaining off.
Bluetooth Neon: The Bluetooth neon will remain illuminated while
successfully paired to another device.
Setting the Desired Temperature
The desired temperature can be set using the '
temperature can be set from 5˚C to 30˚C and this will be shown on the display.
When the temperature is reached the heater will automatically switch OFF. If
the ambient temperature drops the heater will come on again automatically.
Setting the Timer Programmes
There are four program segments available, P1, P2, P3 and P4. For each
segment it is possible to set a desired 'On' time, 'Off' time, Heat mode and
set temperature. It is not necessary to set all four segments if not required.
The default setting is for all segments to be Off. To turn off a pre-programmed
segment it is necessary to set both the 'On' time and the 'Off' time to 00:00.
In order to set up a time/temperature profile the following steps must be
completed:
1. To activate the programming screen press the ' ' key. The program settings
screen for P1 will be displayed and the time will be flashing. This flashing
time is the 'On' time for P1 and can be adjusted using arrow keys. Once the
desired 'On' time has been set press the ENTER key to confirm the time.
2. Select a heat setting using the arrow keys and confirm the selection using
the ENTER key.
3. Set the desired temperature using the arrow keys and confirm the setting
using the ENTER key.
4. The 'Off' time must then be set by using the arrow keys, it is necessary to
then press the ENTER key to confirm the 'Off' time setting.
5. The setup screen will then revert to the P1 'On' time set up screen, at this
point it is possible move to the P2 segment by pressing the ' ' key.
Fig. 11
6. If required P2, P3 and P4 segment can be set up using steps 1-4 above.
7. If it is not required to set up P2, P3 and P4 segment at this stage, continue
to press the ' ' key until the heater reverts to the previous operational mode.
Alternatively if no keys are pressed the programming mode will time out and
revert to the previous operational mode.
Fig. 12
will be displayed on
' or '
' keys. The
Advertisement
