Related Manuals for Case 48048568
Summary of Contents for Case 48048568
- Page 1 1650M Tier 2 Crawler Dozer PIN NGC107000 and above SERVICE MANUAL Part number 48048568 edition English April 2017...
- Page 2 1650M Bulldozer (BD) Blade, Extra Long Track (XLT) - Tier 2 [NGC107000 - ] 1650M Power Angle Tilt (PAT) Blade, Extra Lont Track (XLT) - Tier 2 [NGC107000 - ] 1650M Power Angle Tilt (PAT) Blade, Low Ground Pressure (LGP) - Tier 2 [NGC107000 - ] 48048568 26/04/2017...
- Page 3 [48.138] Track rollers ............... . 48.4 48048568 26/04/2017...
- Page 4 [89.128] Ripper assembly ..............89.1 Platform, cab, bodywork, and decals ..........90 48048568 26/04/2017...
- Page 5 Thanks very much for your reading, Want to get more information, Please click here, Then get the complete manual NOTE: If there is no response to click on the link above, please download the PDF document first, and then click on it. Have any questions please write to me: admin@servicemanualperfect.com...
- Page 6 [90.100] Engine hood and panels ............90.3 48048568 26/04/2017...
- Page 7 INTRODUCTION 48048568 26/04/2017...
-
Page 8: Table Of Contents
Product identification - Machine orientation ..........73 (*) See content for specific models 48048568 26/04/2017... -
Page 9: Foreword - Important Notice Regarding Equipment Servicing
In any case, no warranty is given or attributed on the product manufactured or marketed by the manufacturer in case of damages caused by parts and/or components not approved by the manufacturer. -
Page 10: Safety Rules
NOTE: Note indicates additional information that clarifies steps, procedures, or other information in this manual. Throughout this manual you will find the word Note followed by additional information about a step, procedure, or other information in the manual. The word Note is not intended to address personal safety or property damage. 48048568 26/04/2017... -
Page 11: Safety Rules - Personal Safety
When using auxiliary batteries or connecting jumper cables to start the engine, use the procedure shown in the oper- ator’s manual. Do not short across terminals. Follow manufacturer’s instructions when storing and handling batteries. Battery post, terminals, and related accessories contain lead and lead compounds. Wash hands after handling. This is a California Proposition 65 warning. 48048568 26/04/2017... - Page 12 Wear Personal Protective Equipment (PPE) such as hard hat, eye protection, heavy gloves, hearing protection, pro- tective clothing, etc. Do Not Operate tag Before you start servicing the machine, attach a ‘Do Not Operate’ warning tag to the machine in an area that will be visible. 48048568 26/04/2017...
-
Page 13: Safety Rules - Ecology And The Environment
Improper disposal of batteries can contaminate the soil, groundwater, and waterways. CASE CONSTRUCTION strongly recommends that you return all used batteries to a CASE CONSTRUCTION dealer, who will dispose of the used batteries or recycle the used batteries properly. -
Page 14: Safety Rules - Do Not Operate Tag
D. DO NOT OPERATE - (Warning!) E. REASON - (Area for describing malfunction or service required before operation.) F. Signed by - (Signature area - to be signed by the person validating the reason for installation of the tag.) 48048568 26/04/2017... -
Page 15: Torque - Minimum Tightening Torques For Normal Assembly
762 N·m (560 lb 1016 N·m 501 N·m (370 lb 693 N·m (510 lb (500 lb ft) (750 lb ft) NOTE: M4 through M8 hardware torque specifications are shown in pound-inches. M10 through M24 hardware torque specifications are shown in pound-feet. 48048568 26/04/2017... - Page 16 838 N·m (618 lb 1118 N·m 552 N·m (407 lb (824 lb ft) IDENTIFICATION Metric Hex head and carriage bolts, classes 5.6 and up 20083680 1. Manufacturer's Identification 2. Property Class Metric Hex nuts and locknuts, classes 05 and up 20083681 48048568 26/04/2017...
- Page 17 (465 lb ft) (620 lb ft) (656 lb ft) (875 lb ft) NOTE: For Imperial Units, 1/4 in and 5/16 in hardware torque specifications are shown in pound-inches. 3/8 in through 1 in hardware torque specifications are shown in pound-feet. 48048568 26/04/2017...
- Page 18 SAE Grade Identification Grade 2 - No Marks Grade 2 Nut - No Marks Grade 5 - Three Marks Grade 5 Nut - Marks 120° Apart Grade 8 - Five Marks Grade 8 Nut - Marks 60° Apart 48048568 26/04/2017...
- Page 19 Corner Marking Method (1) Flats Marking Method (2) Clock Marking Method (3) Grade A No Notches No Mark No Marks Grade B One Circumferential Notch Letter B Three Marks Grade C Two Circumferential Notches Letter C Six Marks 48048568 26/04/2017...
-
Page 20: Torque - Standard Torque Data For Hydraulics
207 N·m (152.7 lb ft) M48x2 440 N·m (324.5 lb ft) 264 N·m (194.7 lb ft) M60x2 525 N·m (387.2 lb ft) 315 N·m (232.3 lb ft) NOTE: Final torque tolerance +/– 10% of the given torque specification. 48048568 26/04/2017... - Page 21 660 N·m 660 N·m 396 N·m 396 N·m G 1-1/2 A 38 mm 42 mm (486.8 lb ft) (486.8 lb ft) (292.1 lb ft) (292.1 lb ft) NOTE: Final torque tolerance is +/– 10% of the given torque specification. 48048568 26/04/2017...
- Page 22 (232.3 lb ft) 630 N·m 630 N·m 396 N·m 396 N·m M48x2 32 mm 36 mm (464.7 lb ft) (464.7 lb ft) (292.1 lb ft) (292.1 lb ft) NOTE: Final torque tolerance +/– 10% of the given torque specification. 48048568 26/04/2017...
Need help?
Do you have a question about the 48048568 and is the answer not in the manual?
Questions and answers