Using The Remote Control - Epson PowerLite 600p Product Information

Light Status Description and action
Flashing The projector is too hot. Make sure the
orange temperature surrounding the projector does
not exceed 95 °F and there is plenty of space
around and under the projector for ventilation.
Clean the air filter if necessary.
Red The projector is overheating, which turns off
the lamp automatically. Let it cool for a few
minutes, then turn it back on. Make sure there
is plenty of space around and under the
projector for ventilation. If it continues to
overheat, you may need to change the air
filter.
Flashing red There is a problem with the cooling fan or
temperature sensor. Turn off the projector and
unplug it. Contact EPSON for help.
Using the Control Panel
Power
Computer/YCbCr
Menu
Tracking -
Shift
A/V Mute
The following table summarizes the functions on the control
panel.
Button Function
Power Starts or stops projection.
Help Displays the online help menu.
Computer/ Switches between the source connected to the
YCbCr Computer 1 port and the Computer 2/Component Video
port.
Video Switches between composite video and S-Video.
Menu Displays or hides the menu screen.
Esc Stops the current function. Pressing Esc while viewing a
menu or the online help displays the previous screen or
menu.
Help
Video
Source
Esc
Sync+
Tracking +
Auto
Keystone
Sync-
Resize
Volume
EPSON PowerLite 600p/811p/820p Projectors
Button Function
+
Sync Use after tilting the projector (extending its foot) to
Sync – square up the image. Corrects up to a ±30° tilt. Allows
selection of a menu or menu options if the menu screen
is displayed. When used with the Shift button,
synchronizes the computer's graphic signal. Use these
buttons to adjust a fuzzy-looking image that contains a
lot of fine detail.
Tracking – Corrects horizontal keystone distortion, which occurs
+
Tracking when the projector is not directly in front of the screen.
Allows selection of menu options if the menu screen is
displayed. When used with the Shift button, matches
the projector's internal clock to computer graphic
signals. Use these buttons to eliminate vertical stripes or
bands from an image that contains a lot of fine detail.
Auto Selects a menu option or the next menu/help screen.
Pressing
displayed optimizes the computer image.
Shift Press with the Sync or Tracking buttons to change their
function from Keystone control to Sync or Tracking.
Resize Resizes non-standard computer video formats so they
appear correctly on screen. Switches the aspect ratio
between 4:3 and 16:9 when video images are being
projected.
A/V Mute Turns off the audio and video. (In the menu system, you
can set whether the screen appears black or blue, or
displays a user logo.)
Volume Adjusts the volume.

Using the Remote Control

The remote control uses a line-of-sight infrared signal. It lets
you access the projector's features from anywhere in the room—
up to 32 feet away. (This distance may be shorter if the remote
control batteries are low.) If you have connected the mouse
cable, you can also use the remote control as a wireless mouse.
The projector may not respond to remote control commands in
these conditions:
❏ The remote control is not turned on (using the switch on its
side)
❏ You are too far away or not within 30° to the left or right of
the front or rear sensor or 15° above or below it
❏ Batteries are weak
❏ Ambient light is too bright
❏ A fluorescent light is shining into the infrared receiver
❏ A strong light source (such as direct sunlight) shines into the
infrared receiver
❏ Other equipment emitting infrared energy is present (such as
a radiant room heater)
4/02 EPSON PowerLite 600p/811p/820p Projectors - 7
Auto when no menu or help screen is