Exmark 109-4173 Setup Instructions
Exmark 109-4173 Setup Instructions

Exmark 109-4173 Setup Instructions

Turf tracer hp

Advertisement

Loose Parts
Note: Use the chart below to verify that all parts have been shipped.
109-4173
Dealer Pack
Part #
Description
103-1309
Warranty Registration Form
103-2106
Key
1-633023
Stud, Fuel Tank
322-3
Screw, HH 5/16-18 x 3/4
3256-23
Washer, 5/16 SAE
1-805005
Washer, Lock 5/16 Heavy
1-633349
Spring, Compression
3296-47
Nut, Nyloc 5/16-18 Thin
323-6
Screw, HH 3/8-16 x 1
98-5975
Washer, Spring Disk 3/8
3290-357
Nut, Whizlock 3/8-16
1-806003
Hairpin, Cotter
1-808280
Pin, Clevis 5/16 x 1
3220-16
Nut, Jam 3/8-24 LH
322-9
Screw, HH 5/16-18 x 1 3/4
3296-29
Nut, Nyloc 5/16-18
1-303335
Tie, Cable 7 15/16 (Large)
1-303287
Tie, Cable 5 1/2 (Small)
109-4175
Literature Pack
Part #
Description
------------
Manual, Operator's
------------
Manual, Parts
103-5466
Manual, Engine Operator's
103-6371
Manual, Engine Operator's
103-6374
Manual, Engine Operator's
109-6435
Sheet, Emissions Warranty
SETUP INSTRUCTIONS
Qty
Use
2
Fill out and return to Exmark
1
Unit ignition
2
2
4
Components to install fuel tank
2
2
2
4
4
Components to install handle assembly
4
3
Components to install the speed control rod assembly
& to connect the lower end of the speed control linkage
1
2
2
Components to install drive lever linkages
2
2
For fastening wiring harness to handle assembly
4
Qty
Use
1
Read before operating machine
1
1
For units with 15HP Kawasaki engines
1
For units with 17HP Kawasaki engines
1
For units with 19HP Kawasaki engines
1
TURF TRACER HP
For Serial Nos. 670,000 and Higher
Page 1 of 5
109-6457 Rev. A

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 109-4173 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Exmark 109-4173

  • Page 1 Note: Use the chart below to verify that all parts have been shipped. 109-4173 Dealer Pack Part # Description 103-1309 Warranty Registration Form Fill out and return to Exmark 103-2106 Unit ignition 1-633023 Stud, Fuel Tank 322-3 Screw, HH 5/16-18 x 3/4...
  • Page 2: Servicing The Battery

    Uncrate Unit CAUTION 1. Remove tractor and mower deck from their crates. POTENTIAL HAZARD ♦ If the ignition is in the “ON” position there is Servicing the Battery potential for sparks and engagement of WARNING: Battery posts, terminals, and related components.
  • Page 3 off a 1/2 turn. This is to allow for normal fuel tank 2. Screw turnbuckle onto both upper and lower expansion and contraction with changes in linkages simultaneously. Note that threads on temperature and fuel levels. Do not over upper linkage are left hand. tighten.
  • Page 4 Connecting Speed Control Linkage Adjusting Drive Lever Linkage 1. Connect the lower end of the speed control 1. Raise rear of machine off of the ground. linkage to the speed control crank located at the top rear of the fuel tank support. Secure with CAUTION clevis pin and hairpin from the bolt bag.
  • Page 5: Servicing The Engine

    two flag terminals that are in the longer lead to 2. Check hydraulic reservoir and if necessary fill the OPC switch in any order. the reservoir to the appropriate level with Mobil 1 15W-50 synthetic motor oil. 2. Continue routing this lead down the right side of the handle and connect the connector on the end 3.

Table of Contents