Advertisement
Quick Links
WWW.HUNDREDFIT.COM
OWNER'S MANUAL
（ 160B-motor ）
CONTENTS
IMPORTANT SAFETY INFORMATION --------------------
EXPLODED-VIEW ASSMEBLY DRAWING ----------------
ASSEMBLY INSTRUCTIONS ---------------------------------
COMPLETE EXPLOSION DRAWING -----------------------
Advertisement
Related Manuals for 100FIT 160B-motor
Summary of Contents for 100FIT 160B-motor
- Page 1 WWW.HUNDREDFIT.COM OWNER'S MANUAL （ 160B-motor ） CONTENTS IMPORTANT SAFETY INFORMATION -------------------- EXPLODED-VIEW ASSMEBLY DRAWING ---------------- ASSEMBLY INSTRUCTIONS --------------------------------- COMPLETE EXPLOSION DRAWING -----------------------...
- Page 2 PARTS LIST -------------------------------------------------------- IMPORTANT SAFETY INFORMATION Please read the instructions and warnings carefully before use, to ensure safe and satisfactory operation of this product. Follow the assembly instructions carefully. Please keep this manual in a safe place for your reference when necessary. Please do not assembly or use this equipment until you read this manual thoroughly &...
- Page 3 Keep your back straight whiles exercising. 12. Before using the equipment, check the handle bar, seat, and the nuts & bolts are securely tightened. 13. For adjustable parts, bear the maximum position in your mind, do not exceed the mark "stop", otherwise will cause risk.
- Page 4 EXPLODED-VIEW ASSMEBLY DRAWING...
- Page 5 ASSEMBLY INSTRUCTIONS...
- Page 6 STEP 1 : ---Attache the front stabilizer(3) to the main frame (1) , and fix it with two sets of flat washers(71) & bolts(72) by allen wrench tightly. ----screw the adjusting foot pad (56) into the main frame (1) tightly. Note: the front stabilizer is with transportation wheels.
- Page 7 --- Fix the pedal support tube (19) onto the mainframe (1) with two sets of curved washers(21)& bolts(22) by spanner tightly. --- insert the pedal pole(54) into the hole as pointed on the main frame, then fix the pedal (11) on the pedal pole (54)with flat washers (40) and lock nuts(32) by spanner tightly and rightly .
- Page 8 --- Connect the console wire(14) with the sensor wire(18) correctly ; then put the console support tube (29) onto the main frame as shown carefully, and fix it with two sets of flat washers(43)& bolts(75)by allen wrench tightly. --- Screw out the screws (76) on the console by spanner and keep them , then connect the console wire(14)-top with the wire on the console (9) correctly.
- Page 9 --- Fix the seat (5) on the seat sliding set (4) with four sets flat washers (43)& screws(68) with allen wrench tightly. ---Slide the seat sliding set(4) onto the sliding rail (7) before fixing the crash pad (28) on the sliding rail (7) with bolt (67) tightly.
- Page 10 STEP5:...
- Page 11 -- Fix the rear stabilizer(2) on the sliding rail （7） with four sets of flat washer (43) ,spring washers(69) & screws(68) by allen wrench tightly STEP6:...
- Page 12 ---Put the spacer bushes (36)into the holes on the sliding rail (7), and connect the sliding rail (7) with the main frame(1) with bolt(66), flat washer(40) and lock nut(32) by spanner tightly. --Fix the sliding rail (7) to the main frame (1) with washer (55) and knob(10) tightly. Put the plug (65) into the hole on the sliding rail (7) Now the equipment is completed assembled, if you find it not leveled on the floor, you can adjust it by the adjusting tube plug (13)&the adjusting foot pad(56).If you want to start to exercise ,then...
- Page 13 PARTS LIST...
- Page 14 NAME QTY. NAME QTY. Main frame magnet plate Rear stabilizer flat washer Front stabilizer revolving shaft Seat sliding set circlip SeatMain fra screw Pulley Flywheel axle Sliding rail Bearing Handle bar Screw Console Knob Guide pulley sleeve Pedal Belt guide pulley tube plug left-front stabilizer M10*1.5 Bolt Adjusting tube plug-rear stabilizer...
- Page 15 CONSOLE INSTRUCTION [DISPLAY FUNCTION:] ITEM DESCRIPTION ‧ Stoke per minute ‧ Display range 0~999 ‧ Workout time display during rowing. ‧ Display range 0:00~99:00 Time/500m ‧ Scan every 6 seconds, Computer will display the time needed to row 500 meters according to current speed.
- Page 16 Plug in power supply, computer will power on and display all segments on LCD for 2 seconds. Enter into clock and calendar setting mode. After 4 minutes without rowing or pulse input, console will enter into power saving mode. And display clock, calendar and room temp.
- Page 17 Race Mode ： 1. Press UP or DOWN to select Race mode and press ENTER to confirm. 2. Press UP or DOWN to preset Challenge level and press ENTER to confirm. (Total level =15, L1=1:00 TIME/500M, L15=8:00 TIME/500M, Increments default: 0:30 TIME/500M, Meters default:500M) 3.
- Page 18 3. Press ENTER to complete or exit the setting. 4. Set TIME(or Meters), STROKES, CALORIES, and PULSE values using UP or DOWN keys and press ENTER to confirm. (Time and Meters can not be set at the same time. )) 5.