FS-IA6B接收机与伺服器连接 Receiver and servo connections 为了让发射及接收距离更远,请注意以下几点: 1、尽量保证双天线笔直,否则将会减小控制范围; 2、双天线的夹角保持在90°(如图三种方式),这并不是精确的垂直角度,重要的是尽可能保持天线互相远离; 3、天线应该尽可能远离金属导体,至少要有l.5cm左右的距离。轴电缆段不受此限制,但不要过度弯曲; 4、尽可能保持天线远离电动机、调速器,和其它的噪声源。 In order to make sure maximum distance between the transmitter and receive can be obtained please follow the directions below: 1. The two antennas must be kept as straight as possible. Otherwise, control range will be reduced.
Page 3
Battery 开关 Switch Aux.2襟翼 Aux.1起落架 UPDATE B/VCC 方向舵机 4.0-6.5V/DC Rudder servo 6 CHANNELS RECEI VER 油门舵机 FS-IA6B PPM/CH1 Throttle servo 升降舵机 接收机 Receiver evator servo 副翼舵机 接收机和固定翼的连接方法,例如: Alieron servo 结构:副翼+襟翼+起落架 Connection method for the receiver and the fix wing, for example:...
Page 4
接收机操作说明 Receiver operation instruction 接口说明 Port Setup CH1-CH6: 表示接收机的相应通道; Bind,VCC: 表示用于对码和输入电源的通道; OUT:表示输出PPM数据的i-BUS接口,用于连接串行总线接收 机,扩展通道; IN:表示各种传感器数据的输入接口,数据采集模块可随意串接; CH1/PPM: 表示CH1输出通道兼有PPM信号输出功能 CH1-CH6: represent relevant channel of transmitter. Bind,VCC: represent the channel used for matching and input power respectively. OUT: Represent i-BUS port of outputting PPMS data and be used (Pic 12.1) for connecting the serial bus receiver to expand channels.
Page 5
i-bus Receiver Connection instruction Setup FS-CEV04 i-BUS 串行总线接收机连接说明 功能说明: 此功能是为了应对某些模型通道太多而做的,当通道不够时可采用此配件,来增加通道输出。 串行总线接收机,最多可串联4个模块,共16个通道;按键K1-K4分别对应C1-C4, 用于对相应通道的设定; 操作说明: 1. FS-CEV04 i-BUS接收机的“IN”端口对应接收机的“OUT”端口; 2. FS-CEV04 i-BUS接收机的“OUT”端口,用于串接后级的FS-CEV04接收机,以串联的 方式使用。 3. 将此总线接收机插入接收机,打开己配对的发射机,接收机电源,LED点亮; 4. 操作发射机触控屏,选择接收机设定的主菜单,进入到舵机设定界面; 5. 选择需要扩展的通道,此时,总线接收机的LED熄灭; 6. 用对码线上的胶针,按下需要的,相应通道的按键,LED自动点亮,表示设定成功; 7. 插入舵机,检查设定是否成功; (Pic 12.3) 8. 重复以上操作即可完成总线接收机4个通道的设定; 9. 当需要更多的通道扩展时,只需要在第一级总线接收机的“OUT”端口,串接新的总线接收机即可,设定的操作方法相同。 Function Details : The system is able to support many channels. This allows the user of the system to change to a different output channel should signal strength be insufficient i-BUS receiver, can connect 4 modules with 16 channels in serial at most.
Page 6
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.