Table of Contents
Advertisement
Quick Links
Installation and Maintenance Instructions
XPG170 Electric Fires
PLEASE READ THESE INSTRUCTIONS CAREFULLY AND
RETAIN FOR FUTURE REFERENCE
Your PUREGLOW electric fire has been made with great care. Here are some instructions
including cleaning and maintenance, which will help you keep your fire in good condition
for many years. If you experience any parts or service problems contact either your
retailer or PUREGLOW LIMITED.
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety. Children should be supervised to ensure that they do not play
with the appliance.
This is an amendment to the standard and now applies to all EN60335 items.
PUREGLOW LIMITED
Stour Vale Road
Lye, Stourbridge, DY9 8PP
Telephone: +441384 893060
Fax: +441384 897728
Email: sales@pureglowltd.co.uk
Web: www.pureglowltd.co.uk
1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for PUREGLOW XPG170
Summary of Contents for PUREGLOW XPG170
- Page 1 PLEASE READ THESE INSTRUCTIONS CAREFULLY AND RETAIN FOR FUTURE REFERENCE Your PUREGLOW electric fire has been made with great care. Here are some instructions including cleaning and maintenance, which will help you keep your fire in good condition for many years. If you experience any parts or service problems contact either your retailer or PUREGLOW LIMITED.
-
Page 2: Section 1: Unpacking, Electrical Installation And General Safety
YOUR FIRE XPG fires are visual effect fires with LED lighting and remote control. They are available with several different fascia trims and frets. The general fitting instructions refer to all models. SECTION 1: UNPACKING, ELECTRICAL INSTALLATION AND GENERAL SAFETY GENERAL Unpack the fire carefully and retain the packaging for possible future use, for example in the event of moving home or returning the fire for repair to your supplier. - Page 3 THIS FIRE MUST BE INSTALLED IN A FIREPLACE OPENING AND SECURED USING APPROPRIATE WALL FIXINGS Your PUREGLOW fire is designed to fit a standard 16”(410mm) fireplace opening. Before installing, thoroughly clean the fireplace and ensure debris and dust cannot enter the fire from the chimney;...
-
Page 4: Section 2: Controls
SECTION 2: CONTROLS REMOTE OPERATION On first use insert the batteries into the remote control handset—see battery replacement section. With the mains supply connected to the fire and switched on the fire can be operated. Care DO NOT drop - DO NOT immerse in liquids - DO NOT leave flat batteries in the unit - Clean only with a dry cloth As this product operates using infra-red, ensure there is a clear line of sight between the handset and the appliance for it to operate effectively. -
Page 5: Section 3: Maintenance And Cleaning
LED’s or failure of the LED power supply — in this case the fire must be returned to Pureglow Ltd for replacement. REMOTE HANDSET BATTERY REPLACEMENT To replace the batteries in the remote handset remove the battery compartment cover and remove the batteries. -
Page 6: Section 4: Important Information
SECTION 4: IMPORTANT INFORMATION To avoid risk of explosion, never throw batteries into a fire or expose batteries to any strong heat sources. DO NOT SWALLOW. If a battery is swallowed you should seek immediate medical attention. DO NOT dispose of this battery in your normal household waste; once the battery has reached the end of it’s life it should be taken to a recycling centre. - Page 7 ZARA / CARMEN CASTINGS The casting complete with magnets are positioned as shown in Fig 3 below and moved towards the fire back so as to align with the canopy but slightly raised off the hearth (to avoid scratching the hearth); it is moved back until the magnets attach to the fire back flanges then moved down onto the hearth as shown in Fig 4, the ashpan and fuel bed can now be fitted (see Section 6 for fuel bed layout).
- Page 8 SECTION 5 CTD: FITTING THE CANOPY & FRAME FITTING THE CANOPY If the Fire is supplied without the canopy fitted then it should be fitted prior to installing into the Fireplace as shown by the diagram right. The 4 Tabs (2 each side) line up with slots either side of the Fire back;...
-
Page 9: Fitting The Fret
The fire should now look like the diagram (right), now the fret can be fitted. NOTE: The stability bracket shown is only required if the fire is NOT fixed into the fireplace FITTING THE FRET The fret is fitted as shown on the diagram (right), care should be taken when positioning the fret to make sure that the fireplace hearth is not damaged. -
Page 10: Section 6: Fuel Beds
SECTION 6: FUEL BEDS. The Fire is supplied with the Fuel bed and back panel fitted, when the fire has been fitted into the Fireplace all that is required to complete the installation is to remove the transit tape which holds the Fuel bed and back panel in place during transit and fitting. The Log bed is also supplied with loose logs that are laid out after the above is complete, see ‘Log bed assembly layout’... - Page 11 LOG BED...
- Page 12 FUEL BED / REAR PANEL RETENTION Removal of the log/coal fuel bed and rear panel: 1. Ensure the fire is switched off 2. Carefully remove individual logs from the log bed (note: the coals are fixed to the coal bed and are not intended to be removed individually) 3.
-
Page 13: Section 7: Freestanding Spacer Frame
SECTION 7: FREESTANDING SPACER FRAME. The Spacer frame is fitted using the included 6-off self tapping screws as shown below. MODELS WITHOUT CANOPY MODELS WITH CANOPY STABILITY BRACKET STABILITY BRACKET THE FIRE CAN ONLY BE USED AS SHOWN ABOVE WITH THE STABILITY BRACKET INSTALLED WHERE POSSIBLE THE FIRE SHOULD BE INSTALLED AS SHOWN BELOW USING THE WALL HANGER BRACKET. -
Page 14: Short Parts List
Only genuine spares should be used, and these can normally be obtained from your re- tailer. If you have any problems contact PUREGLOW Ltd at the address on the front of these instructions. Below is a list of the most common parts. - Page 15 GUARANTEE This product is guaranteed against faulty parts or workmanship for 3 years from the date of purchase. To validate the guarantee the product must be returned to the retailer or supplier for repair or replacement with this sheet completed with the detail requested. (Please do not send a photocopy).
- Page 16 Packing list Remote Handset Batteries Affix Second Data Mains Lead Label HERE Packed By Date Log bed + Logs x4 Coal bed Back panel brick/reed Packed By Date Model Type Pureglow XPG 2kW...
Need help?
Do you have a question about the XPG170 and is the answer not in the manual?
Questions and answers