Table of Contents
Advertisement
Quick Links
NOVO
HIGH EFFICIENCY GAS FIRE
MODELS : P23G, L23G
INSTALLATION AND USER INSTRUCTIONS
All instructions must be handed to user for safekeeping
Revision D - 11/09
Country(s) of destination - GB/IE
W J Court & Sons Limited • Stourvale Road • Lye • Stourbridge • West Midlands • DY9 8PP
Tel: +44 1384 893060 • Fax: +44 1384 897728 • e-mail:info@pureglowltd.co.uk
Advertisement
Table of Contents
Related Manuals for PUREGLOW NOVO P23G
Summary of Contents for PUREGLOW NOVO P23G
- Page 1 NOVO HIGH EFFICIENCY GAS FIRE MODELS : P23G, L23G INSTALLATION AND USER INSTRUCTIONS All instructions must be handed to user for safekeeping Revision D - 11/09 Country(s) of destination - GB/IE W J Court & Sons Limited • Stourvale Road • Lye • Stourbridge • West Midlands • DY9 8PP Tel: +44 1384 893060 •...
- Page 2 P23 Novo graphite P23 Novo passion flower L23 Novo chrome P23 Novo maple leaf...
-
Page 3: Installation Instructions
INSTALLATION INSTRUCTIONS Preliminary Notes Before Installation This appliance is a high efficiency, flueless, flame effect gas fire. It provides radiant and con- vected warmth both efficiently and safely utilising the latest type catalytic convertor burner technology. The appliance incorporates a combustion monitoring system (Oxygen Depletion System). It must not be adjusted or put out of operation. -
Page 4: Table Of Contents
Section Contents Page No. Section Contents Page No. Important Notes Testing and Commisioning Appliance Data Operating the Appliance Installation Requirements Spark Failure 3.1 Room Sizing Setting pressure Site Requirements Fitting the Decorative Frame 4.1 Ventilation Briefing the customer Unpacking the Appliance 10.0 Servicing 5.1 Component Checklist... -
Page 5: Appliance Data
APPLIANCE DATA Model L23 Novo P23 Novo L23 Novo LPG P23 Novo LPG Gas Group Gas Category Inlet Pressure (±2.0mbar) 20 mbar 20 mbar 37 mbar 37 mbar Max Energy Input (Gross) 2.0 kW 2.0 kW 1.7 kW 1.7 kW (Net) 1.8 kW 1.8 kW... -
Page 6: Ventilation
SITE REQUIREMENTS (continued) Clearances to non-combustibles Non combustible surfaces are defined as brick, metal, marble, concrete etc. and also a number of man-made materials impervious to flame. If in doubt refer to the material manufacturer for further information before pro- ceeding with installation. -
Page 7: Unpacking The Appliance
VENTILATION (continued) Any ventilation fitted must comply with BS 5871 part 4 and BS 5440 part 2. Ventilation fitted under, or within immediate vicinity of the appliance must not be used as it may adversely effect performance of the ODS system. The appliance MUST NOT be installed in a bedroom, bathroom or any sleep- ing area. -
Page 8: Checking The Burner
FIXING THE APPLIANCE F860059 ISSUE A - 25/5/06 POSITION SPIRIT LEVEL ALONG THIS EDGE TO LEVEL WALL MOUNTED P23G & P23E TEMPLATE BEFORE MARKING OUT WALL FITTING TEMPLATE Do not block the ventilation holes of the appliance. The wall onto FIXING POINTS FOR GAS MODEL P23G FIXING POINTS FOR ELECTRIC MODEL P23E which the appliance is installed must be flat. -
Page 9: Testing And Commissioning
TESTING AND COMMISSIONING Turn on and test the gas supply up to the fire for any leaks, in accordance with the current edition of BS 6891 (natural gas installations) or BS 5482 pt1 (propane installations) . OPERATING THE APPLIANCE The pilot is visible behind the left hand side of the burner. ‘OFF’... -
Page 10: Fitting The Decorative Frame
FITTING THE DECORATIVE FRAME ASSEMBLY Remove the decorative frame assembly from any protective packaging, and remove any pro- tective film that may be present on the frame. Attach the frame support brackets to the frame using two screws to retain each bracket. Note - the top frame support brackets are of a hooked design, and the lower brackets feature a hole. -
Page 11: Servicing The Burner Unit
10.1 SERVICING THE BURNER UNIT AND GAS ASSEMBLY Firstly, remove the decorative frame assembly per the reverse of section 8.4, the glass panel, and disconnect the gas connection inside appliance. The gas connections to the gas valve can now be released. Detatch the burn- er front cover plate by removal of the four retaining screws. -
Page 12: Testing For Firebox Leakage
10.3 CATALYST (continued) Now divide the concentration of carbon monoxide (CO) expressed in percent by the concentration of carbon dioxide (CO2) to obtain the appliance combustion ratio. CO (%) CO2 (%) = ratio The combustion ratio of the gasses emitted by the catalytic convertor should not exceed 0.0015. If replacing, firstly, remove the decorative fireframe as described in section 8.4. -
Page 13: User Instructions
USER INSTRUCTIONS Section Content Page No Important Notes Clearances to Combustibles Ventilation & Room Size Operating Instructions Combustion Monitoring System Cleaning Servicing List of Replacement Parts IMPORTANT NOTES The installation and Servicing of this fire MUST only be carried out by a competent person (such as a Gas Safe registered fitter) in accordance with the Gas Safety (Installation and Use) Regulations 1998, the relevant British Standards, Codes of Practice, the Building Regulations and the manufacturer's instructions. -
Page 14: Clearances To Combustibles
CLEARANCES TO COMBUSTIBLES Clearances to combustible materials Combustible materials are defined as wood, fabrics, or other materials likely to combust if exposed to flame. Generally, any material, which is likely to discolour, melt or misshape when exposed to moderate heat, should be considered as a combustible material or surface. -
Page 15: Operating Instructions
VENTILATION AND ROOM SIZE Purpose provided ventilation of 100cm 2 is required for this appliance. An openable window or equivalent is also required. The appliance should not be installed within 500mm of any air vent. Any ventilation fitted must comply with BS 5871 part 4 and BS 5440 part 2. Ventilation fitted under, or within immediate vicinity of the appliance must not be used as it may adversely effect performance of the combus- tion monitoring system (ODS) system. -
Page 16: List Of Spare Parts
CLEANING Before carrying out any of the following operations, ensure that the appliance is OFF and completely cold. GLASS PANEL - This can be cleaned with a suitable glass cleaner, or proprietary ceramic hob cleaner. Test on a small area first. PAINTED AREAS - These can be cleaned using a dry cloth.
Need help?
Do you have a question about the NOVO P23G and is the answer not in the manual?
Questions and answers