Safety Instructions Before using this product, please read the safety instructions and follow all those regular safety precautions. 1. Only authorized technicians can disassemble the product. Users are not allowed to disassemble or repair the product. 2. Only use the original battery and power adapter of the product for charging. Using an unmatched adapter may cause electric shock, fire or product damage.
Product Features Powerful Suction & Intelligent Suction Adjustment Powerful Suction Suction power of this product is strong enough to ensure that even tiny dust on the floor will be cleaned thoroughly! Intelligent Suction Adjustment This product is able to automatically adjust its suction power when different floor environments are detected.
Page 5
Product Features 2. Spot cleaning mode The robot will clean intensively in a spiral way when it detects a very dirty area. 3. Edge cleaning mode In this mode the robot will clean along the wall or obstacles. 4. Scheduling mode After scheduled, the robot will leave charging station and start working at scheduled time.
Product Components Main body and accessories Description Quantity Main Body Charging Station Adapter Remote Control (battery not included) HEPA Filter Cleaning Brush Side Brushes *2 and Spare Brushes *2 User Manual...
Product Components Note: A. Install two AAA type batteries into the remote before use. B. Remove the batteries if the remote will be left unused for a long period. C. If you use the remote near charging home base, the robot may not recognize command and may not work.
Product Components Display Panel LED Panel 1. “ ”: LED panel LED panel shows the time setting, charging status, and error codes by using numbers, letters or graph. Buttons 2. “ ” : UV light button In standby mode, press this button to preset the UV light status (on/off). When robot starts cleaning, the UV light will turn on/off as preset.
Product Operation 1. Battery charging A. Positioning the charging station: Place the charging station against the wall and remove obstacles 1 meter on either side and about 2 meters front of the charging station, as shown in the image. B. To charge, make sure the “ON/OFF” switch on the side of the robot is switched to “ON”. C.
Product Operation 2. Starting up/ Standby/ Sleeping/ Power off A. Starting up a. Press the “ON/OFF” switch on the side of the robot to “ON”. b. Press on main body or ON/OFF on remote control to start cleaning. Note: If robot is in sleeping mode, press on main body or ON/OFF on remote control to wake up the robot from sleeping mode, then press again, the robot will...
Product Operation 3. Scheduling You can schedule the robot to make it start cleaning automatically at a certain time every day. Scheduling by keys on the main body Note: The robot can only be set when it’s in Standby or Charging mode. If the robot is in sleep mode, press on main body or ON/OFF button on remote control to wake up the robot.
Cleaning Modes Please touch the button to start cleaning. You can only select the cleaning mode when the robot is cleaning, press the MODE button on remote control to select the cleaning mode, the mode type will appear on the robot’s 4 Digits LED Display as follow: A.
Product Maintenance 1. Cleaning Side Brushes Clean the side brush when it gets dirty and replace it if it's damaged. Max life span for side brush is 12 months. Note: Before replacing side brushes, check and make sure the 'L' / 'R' mark on side brush match with the 'L' / 'R' mark on the bottom base of the robot.
Product Maintenance 3. Cleaning Sensors and Wheels Slightly wipe all the sensors and wheels, as marked in figure below, with soft cleaning cloth or tool. 4. Cleaning Charging Poles Clean the charging poles, as marked in figure below, with soft cleaning cloth or tool. 5.
Page 16
Troubleshooting Error Code for Sensors Cause Error Code Solution Suction passage blocked AUBF Clean suction passage Dust bin not placed in position or robot without Put back dust bin and place it in position AUBN dust bin Left collision switch fault E1XX Right collision switch fault E2XX...
Troubleshooting Error Code for Sensors Error Code Cause Solution Left anti-drop sensor detects cliff, front bumper right EXX9 infrared sensor detects obstacle Front anti-drop sensor detects cliff, front bumper right EXXA infrared sensor detects obstacle Left and front anti-drop sensors detect cliff, front EXXB bumper right infrared sensor detects obstacle Right anti-drop sensor detects cliff, front bumper right...
Page 18
Troubleshooting Troubleshooting for Motors Error code Cause Solution Check if fan is pressed, and clean L01X Fan overloaded dust bin L0X1 Left wheel overloaded L0X2 Right wheel overloaded L0X3 Left and right wheels overloaded L0X4 Left side brush overloaded L0X5 Left wheel and left side brush overloaded L0X6 Right wheel and left side brush overloaded...
Battery Removal 1. Remove the screws on battery cover with a screw driver. 2. Remove the battery cover. 3. Grasp the insulating tape at two sides of the battery and lift the battery. 4. Unplug the wire connector that links the battery and robot. Note: Only use the original battery of the product, otherwise it may cause product damage.