Epson Stylus C82WN Start Here

Start Here

EPSON Stylus ® C82WN
Follow these instructions if you're an advanced user and your network has a
wireless access point or AirPort TM Base Station. This includes wired networks
that have wireless access points. For more detailed instructions, see your
Setup and Installation book.
1
Unpack and
Set Up the Printer
1
Take everything out of the box.
Print server base Setup and Printer Basics
Installation
Print server
Printer software
Parallel cable CD-ROM Paper support
Print server
power supply
Ink
cartridges
Printer
2
Remove all the tape and packing material inside and around the printer.
The tape may be in different places on your printer, so check carefully.
3
Slide the paper
support into the
grooves as shown.
It should fit securely.
4
Plug in the printer and
press the power
button until the green
light comes on.
Power
button
5
Lower the output tray and open the cover.
6
Shake the package of ink cartridges
4 or 5 times. Then remove the cartridges
from the package.
continue
7
Insert each cartridge into its holder
and push it into place.
Note: Don't remove the cartridge labels,
or ink may leak.
8
Press the ink button and close the
printer cover. Wait while the ink charges.
Caution: Don't turn off the printer while the green light is flashing, unless
the printer hasn't moved or made any noise for more than 5 minutes.
9
Place paper against the right edge
of the sheet feeder, then slide the
edge guide against the paper.
10
Pull out the output tray extensions.
To check the printer, first turn it off. Then hold
down the paper button as you press and
release the power button to turn it back on.
The test page prints.
If the test page doesn't print, see the "Problem Solving" chapter
in Printer Basics.
2
Install the Software
Follow the appropriate instructions below to install the software if you
have a wireless access point or AirPort Base Station. If you don't, see your
Setup and Installation book.
Windows ®
1
Make sure the wireless mode for your computer is set to Infrastructure
and WEP encryption is disabled.
For instructions, see the documentation for your wireless adapter.
2
Insert your printer software CD-ROM.
3
Double-click Install EPSON
Stylus C82WN Printer Driver
and follow the instructions
on the screen.
4
When you see this window, click
Stop searching. Then follow the
instructions on the screen to finish
installing and register your printer.
Note: The Stop Searching button
may take a minute or two to appear.
5
Double-click Install EPSON Status Monitor on the EPSON
Installation Program screen and wait while the files are copied.
6
Double-click Install EPSON Printer Information Center and
follow the on-screen instructions to install the information center.
7
Double-click Install EpsonNet Wireless Print Server Utilities.
8
If you see this message click Continue.
Caution: You must install the
Java Runtime Environment if it's
not already installed on your computer.
9
When you see the license agreement, read it and
click Yes to continue. Follow the instructions on the screen.
continue
10
When you see this window
select Program Files and
WP-Admin and click Next.
You see the Wireless
Server Search Window.
Continue with the instructions in section 3, "Connect the Print Server."
Macintosh
®
1
Before you begin, do the following:
•
Make sure that AirPort is on and that both AppleTalk ® and
TCP/ IP are enabled.
•
Select a working connection to an AirPort Base Station or to an
access point.
•
Make sure that WEP encryption is disabled on your wireless network.
For details, see your AirPort or Macintosh documentation.
2
Insert your printer software CD-ROM.
3
Mac ® OS X: Double-click the EPSON CD-ROM icon to open it,
then double-click the Software for OS X folder. Double-click the
C82Series icon, and enter your administrator password, if necessary.
Mac OS 8.6 to 9.x: Double-click the Software for OS 8.6-9.x folder
in the EPSON window (you may have to double-click the EPSON
CD-ROM icon on your desktop to open the window). Double-click the
Printer Driver Installer folder, then double-click the Stylus C82WN
Installer icon.
4
Click Continue.
5
Follow the instructions on the screen to install the printer driver and
restart your Macintosh.
6
If necessary, double-click the EPSON CD-ROM icon to open your
EPSON window.
7
Do one of the following:
Mac OS X: Double-click the Software for OS X folder if necessary,
then double-click the Printer Information Center icon. Follow the
on-screen instructions to install the information center.
Mac OS 8.6 to 9.x: Double-click the Software for OS 8.6-9.x folder,
then double-click the Printer Information Center folder. Double-click
the Printer Information Center icon and follow the on-screen
instructions to install the information center.
8
Do one of the following:
Mac OS X: Double-click the
Wireless Utility Installer icon.
Mac OS 8.6 to 9.x:
Double-click the Install
Wireless Utility folder, then
double-click the Wireless
Utility Installer icon.
You see the print server
install window:
9
Click Next.
10
Read the license agreement. Click Next to accept the agreement
and continue.
11
Follow the instructions on the
screen to install WP-Admin.
At the last screen, click Done.
You see the Wireless Server
Search window.
Continue with the instructions in section 3, "Connect the Print Server" .
3
Connect the Print Server
1
Slide the print server into the base and press firmly.
2
Turn off the printer. Then connect the parallel cable to the printer
and print server.
3
Connect the power supply to the print server and plug in the AC
adapter. Both the green and yellow lights come on and then go out.
4
Turn on the printer.
5
To test the connection, press the test button for one second
and release it. The status page prints.
Test button
If the status page doesn't print, or it indicates that zero bytes were
transmitted or received, check the solutions under "Problems?"
on the back of this sheet.
Turn over