Epson Stylus C82WN Start Here page 2

4
Configure the Print Server
After the files are installed, you see the Wireless Server Search window:
1
Click START. You see server information like this:
Appears
when the
server is
found Indicates
signal strength
It may take up to 2 minutes for the server information to appear.
If you don't pick up a signal from the print server, move the print server
and access point closer to each other and to the computer. If that
doesn't work, try the solutions under "Problems?."
2
When you see server information on the screen, click STOP.
Then click CONFIGURE.
3
When you see a message asking for a password, click OK.
You see the Wireless Configuration screen:
Note: For descriptions of all the settings on the Wireless
Configuration screen, see Appendix A in Setup and Installation.
4
Enter a Server Name that is easy to remember.
5
Check that Boot Method is set to AUTO. Then click OK.
Note: Always set the Boot Method to AUTO, unless you plan to
unplug the print server. See Setup and Installation for details.
6
When you see the Wireless Server Search window again, click QUIT.
7
Do one of the following:
Windows: Click Finish on the last screen. Then continue with
the instructions in the next section to set up a network port.
Mac OS X: Add the printer to the Print Center. (For details, see
Printer Basics.) Congratulations! You're ready for wireless printing.
See Printer Basics for instructions.
Mac OS 8.6 to 9.x: Select your C82 Series printer icon in the
Macintosh Chooser. Congratulations! You're ready for wireless
printing. See Printer Basics for more information.
5
Set Up a Network Port
You need to add the printer's network port to each Windows computer that
will access it. If necessary, print a status page and note the server name or IP
address of your print server before you begin. For instructions on setting up a
network port on Windows NT, ® see the Setup and Installation book.
Windows XP or 2000
1
Do one of the following:
Windows XP: Click Start > Control Panel > Printers and
Other Hardware > Printers and Faxes.
Windows 2000: Click Start > Settings > Printers.
2
Right-click your printer icon, then click Properties.
3
On the Ports tab, select your printer (if necessary), and click Add Port.
4
Select Standard TCP/IP Port and click New Port.
5
When you see the Add Standard TCP/IP Printer Port Wizard, click Next.
6
Enter your print server name or IP address and click Next.
7
Follow the instructions on the screen to complete the wizard.
8
Click Close to close the printer ports window, then click Apply
on the Properties window.
9
To test the connection, select the General tab and click
Print Test Page.
If the test page prints, click OK to close the Properties window.
If it doesn't print, try the solutions under "Problems" in the next column.
Congratulations! You're ready for wireless printing. See Printer Basics for
more information.
Windows Me, 98, or 95
1
On the EPSON Installation Program screen, double-click Install
EpsonNet Direct Print Utility and follow the on-screen instructions
to install the utility and restart your computer.
2
Click Start > Settings > Printers.
3
Right-click your printer icon, then click Properties. Click the Details tab.
4
Click Add Port.
continue
5
Make sure Network is selected, then click Browse.
6
Click to expand the network path, then click the + next to
Epson _ Ipr and select your printer.
7
Click OK, then click OK again. Click Apply on the Details tab.
8
To test the connection, click the General tab and click
Print Test Page.
If the test page prints, click Yes, then click OK to close the Properties
window.
If it doesn't print, try the suggestions under "Problems?" below.
Congratulations! You're ready for wireless printing. See Printer Basics
for more information.
Problems?
The print server's status Make sure the parallel cable is securely
page doesn't print, or it connected to both the print server and your
indicates that zero bytes computer.
were transmitted
or received. Make sure the printer is on. Check the printer's
lights to see if there is a problem. See Printer
Basics for details.
Unplug the AC adapter from the print server
and plug it in again. Then press the print
server's test button for 10 seconds to reset it to
its factory defaults. If you still have problems,
contact EPSON.
The Wireless Server Make sure the print server, printer, and access
Search window fails to point are not near a cordless phone unit,
pick up a signal from microwave oven, Bluetooth TM device, or large
the print server. metal object. Try moving them to a new
location, or try moving them closer to
each other.
Test button
Press the print server's test button for 10
seconds to reset it. On Macintosh, select your
wireless network again.
Try restarting your computer.
On Macintosh, make sure that AirPort is
on, and that both AppleTalk and TCP/ IP
are enabled.
Confirm the connection between the computer
and your access point or base station. If you
have problems establishing a connection,
reset the access point or base station.
continue
You are getting a wireless Check the Wireless Server Search window to
signal, but you are not make sure your wireless link has adequate
able to print. strength—at least 50 percent. If the signal is
weak, try moving the print server, printer,
and access point or base station.
Signal strength
Make sure that your network port is set up
correctly (Windows), or that you've selected
the printer in the Chooser (Mac OS 8.6 to 9.x)
or added it to the Print Center (Mac OS X).
Check the printer's lights to see if there is a
problem with the printer. See Printer Basics
for details.
You are unable to see the Make sure you are connected to the correct
printer in the Macintosh AirPort network. See your AirPort
Chooser or Print Center. documentation for details.
You see a communication You may see an error message if another
error when you try to print. computer on your network is trying to print at
the same time. Wait until the first print job is
done. Your job will print when it reaches the
top of the print queue.
Paper jams frequently. Try loading fewer sheets of paper.
When you load paper, don't push it in.
Also, slide the left edge guide against the
paper, but not too tightly.
Use new, smooth, high-quality paper.
For more problem solving tips on wireless printing, see Setup and Installation.
For printer problems, see Printer Basics.
Where to Get Help
EPSON Printer Information Center
View Print Show animations that quickly tell you how to load special paper,
replace ink cartridges, and clean the print head. Also includes a Reference
Guide with additional printer information. To launch EPSON Printer
Information Center, double-click the EPIC icon on your desktop.
Printer Basics
Includes instructions for printing, maintaining the printer, and solving
basic printer problems.
Setup and Installation
Provides greater detail about how to set up your printer for wireless network
printing. Includes system requirements, print server specifications, and
descriptions of settings on the Wireless Server Configuration screen.
World Wide Web
From the Internet, you can reach EPSON Support at http://support.epson.com.
Here you can download drivers and other files, look at product documentation
and troubleshooting information, and receive technical advice through e-mail.
Automated Telephone Services
A variety of help services are available 24 hours a day, 7 days a week.
To use these services, you must have a touch tone telephone and call
(800) 922-8911. Your EPSON SoundAdvice SM Express Code is 70400.
Use this code to quickly select the EPSON Stylus C82WN in SoundAdvice.
EPSON and EPSON Stylus are registered trademarks of SEIKO EPSON CORPORATION, and SoundAdvice is
a service mark of Epson America, Inc.
General Notice: Other product names are for identification purposes only and may be trademarks of
their respective owners. EPSON disclaims any and all rights in those marks.
Copyright © 2002 by Epson America, Inc. Printed on recycled paper.
12/02 Printed in USA
CPD-15417