Epson LQ-680Pro User Manual page 4

EPSON LQ-680Pro
Single-sheet multipart forms:
front and high-capacity cut-sheet feeder entry
Width Front
3.5 to 12 inches (90 to 304.8 mm)
High-capacity cut-sheet feeder
3.9 to 11.7 inches (100 to 297 mm)
Length Front, top glue
2.8 to 16.5 inches (70 to 420 mm)
Front, side glue
2.8 to 11.7 inches (70 to 297 mm)
High capacity cut-sheet feeder
2.8 to 16.5 inches (70 to 420 mm)
Copies 1 original up to 5 copies
Thickness 0.0047 to 0.018 inch (0.12 to 0.46 mm)
Weight 10 to 15 lb (40 to 58 g/m
Binding Front
Line glue at the top or side of form
High-capacity cut-sheet feeder
Line glue at the top of form
Envelopes:
front and high-capacity cut-sheet feeder entry
Size No. 6
No. 10
Thickness 0.0063 to 0.0205 inch (0.16 to 0.52 mm)
Weight 12 to 24 lb (45 to 90 g/m
Postcards:
front and high-capacity cut-sheet feeder entry
Width 3.9 to 7.8 inches (100 to 200 mm)
Length 3.9 to 7.8 inches (100 to 200 mm)
Thickness 0.0087 inch (0.22 mm)
Weight 51 lb (192 g/m
Roll paper:
rear entry with optional roll paper holder
Width 8.5 0.12 inches (216
Thickness 0.0028 to 0.0035 inch (0.07 to 0.09 mm)
Weight 14 to 22 lb (52 to 82 g/m²)
Continuous paper (standard and multipart):
rear entry
Width 4 to 12 inches (101.6 to 304.8 mm)
Length 3 to 22 inches (76.2 to 558.8 mm)
Copies 1 original up to 5 copies
4 - EPSON LQ-680Pro
2 )
6.5 3.6 inches (165 92 mm)
9.5 4.1 inches (241 105 mm)
2 )
2 )
3 mm)
Thickness Printable area
0.0025 to 0.018 inch (0.065 to 0.46 mm)
Perforated edges
up to 0.035 inch (0.9 mm)
Weight (not multipart)
Weight (1 multipart sheet) 10 to 15 lb (40 to 58 g/m
Binding Point glue and/or paper staples on both sides
The ratio of the cut/uncut length at the perforation should
be between 3:1 and 5:1.
The thickness of the perforation part when extended should
be 2 mm or less.
The perforation between pages should not extend all the
way to the edges of the paper. Uncut length on the edges
should be 1 mm or more.
When the horizontal and vertical perforation cuts intersect,
do not print in between .12 inch (3 mm) above and below
the horizontal perforation and in between 1.1 inch (28 mm)
left and right of the vertical perforation.
Continuous paper with overlapping multipart
forms: rear entry
Width and length of the backing sheet
Same as standard continuous paper
Copies 1 original + up to 5 copies
Thickness Printable area
0.0025 to 0.018 inch (0.065 to 0.46 mm)
Overlapping area
up to 0.028 inch (0.70 mm)
Labels: rear entry
Label size 15/16
0.1 inch (2.5 mm) corner radius, minimum
Backing sheet width
4 to 12 inches (101.6 to 304.8 mm)
Backing sheet length (one page)
3 to 22 inches (76.2 to 558.8 mm)
Backing sheet thickness
0.0028 to 0.0035 inch (0.07 to 0.09 mm)
Total thickness
0.0063 to 0.0075 inch (0.16 to 0.19 mm)
Label weight 17 lb (64 g/m²)
11/00
14 to 34 lb (52 to 128 g/m
2.5 inches (23.8 63.5 mm) minimum
2 )
2 )