Operation - Black & Decker BCS601 Instruction Manual

30 • ENGLISH
Warning! You should only charge the BLACK+DECKER
GoPak 2 in 1 battery using UL or CSA approved USB ports
rated for charging high performance devices. The GoPak can
pull more current than acceptable with older USB ports. An
error message may display on your computer if the computer
is used to charge the GoPak.
1. Plug the micro USB cable (included) (13) into a USB
power supply (not included).
2. Plug the micro USB plug of your charger cord into the
GoPak micro USB port (12).
3. As the GoPak charges, the state of charge LEDs will
illuminate. The illuminated LED(s) indicate the state
of charge of the pack. The blinking LED indicates the
next level of charge in progress. The state of charge
button (9) is disabled during charging only.
4. The completion of charge is indicated by all four LEDs
turning o. Pressing the state of charge indicator button
(9) will illuminate all four LEDs. The battery is fully
charged and may be used at this time or left on the
charger.
5. Recharge discharged batteries as soon as possible
after use or battery life may be greatly diminished. For
longest battery life, do not discharge batteries fully. It
is recommended that the batteries be recharged after
each use.
State of charge indicator (Fig. D)
The BLACK+DECKER GoPak 2 in 1 battery is equipped
with a state of charge button (9) with a four LED display.
The state of charge is an indication of approximate
levels of charge remaining in the battery according to the
following indicators:
To actuate the state of charge, press the State Of Charge
Indicator button. A combination of the four LEDs will
illuminate designating the level of charge left. When the
level of charge in the battery is below the usable limit, the
state of charge LEDs will either not light or the bottom LED
will blink.
Note: The state of charge LED will only display once the
state of charge button is pressed.
f Press state of charge button at anytime to display the
remaining level of charge.
96-100% charged
76-95%
51-75%
26-50%
Pack needs to be charged
Note: The state of charge Indicator is only an indication of
the charge left on the battery. It does not indicate tool
functionality and is subject to variation based on product
components, temperature and end-user application.
Note: GoPak battery terminal cap should be used when
battery is not connected to a power tool. Terminal cap is
provided for use whenever the battery is out of the tool.
Remove cap before placing battery into tool.
Components (Fig. A)
Warning! Never modify the power tool or any part of it.
Damage or personal injury could result.
f Refer to Figure A at the beginning of this manual for a
complete list of components.
f Do not use under wet conditions or in presence of
flammable liquids or gases.
f Do not let children come into contact with the tool.
Supervision is required when inexperienced operators
use this tool.
Assembly and adjustments
Warning! To reduce the risk of serious personal injury,
turn unit off and remove the battery pack before making
any adjustments or removing/installing attachments or
accessories. An accidental start-up can cause injury.
Fitting the saw blade (Fig. A, F)
1. Hold the saw blade (5) as shown, with teeth facing
forward.
2. Push the locking lever (3) up away from the shoe (4).
3. With the teeth facing forward, insert the shank of the
saw blade into the blade holder (18) as far as it will go.
4. Release the lever.
5. Pull blade to be sure the blade is fully secured.

OPERATION

Warning! To reduce the risk of serious personal injury,
turn unit o and remove the battery pack before making any
adjustments or removing/installing attachments or
accessories. An accidental start-up can cause injury.
Warning! To reduce the risk of injury, never use the tool
when the saw shoe is loose or removed
Installing and Removing the GoPak 2 in 1
Battery in a Power Tool (Fig. F)
Warning! Remove any connected USB cords from the
BLACK+DECKER GoPak 2 in 1 battery before connecting
the GoPak to the compatible tool.
1. Remove the tool terminal cap if installed on the
BLACK+DECKER GoPak 2 in 1 battery.
2. To power a compatible GoPak 12V MAX* power tool,
align the tool terminals on the foot of the tool with the
terminal slots on the battery (6) as shown in Fig. G.
Note: The state of charge indicator will face the rear of the
tool and the USB ports will face the front. The arrow on the