Table of Contents
Advertisement
Quick Links
Bulletin 855H Recordable Horn
855H-R30C, 855H-R45C, 855H-RC30Cx, 855H-RC45Cx
-20°C to +55°C (-4°F to +131°F)
WARNING
AVERTISSEMENT
WARNUNG
ADVERTENCIA
ATENÇÃO
AVVERTENZA
Wiring practices must meet applicable electrical codes.
Les procédures de câblage doivent répondre aux codes électriques en vigueur.
Bei der Verdrahtung sind die geltenden elektrotechnischen Sicherheitsvorschriften zu befolgen.
Le procedure adottate per i cavi devono rispettare le codi che elettriche applicabill.
A instalação da ação deve atender aos códigos elétricos aplicáveis.
Las prácticas de instalación eléctrica deben seguir los códigos eléctricos.
FEATURES:
•
4 stages - Each stage can record up to 30 seconds of CD quality audio
•
Record via on-board microphone or from external source using audio input jack
•
Message can be played back preceded by one of forty five alarm tones, or without any alarm tone if desired
•
Master / Slave functionality allows multiple horns to be set up exactly the same way
•
Optional high-output LED beacon available
•
Horn / LED combination units allow user to select steady or flashing LED function (2 Hz flash rate)
OPERATING AND MARKING:
All units have the following operating requirements and limitations.
855H Horn only units:
Catalog No.
Voltage Range
855H-R30C
10-30V DC
855H-R45C
90-260V AC
(50/60Hz)
Sound Output @ 1 meter:
101 dB (A) Voice
102 dB (A) Music
HORN SET-UP AND RECORDING
Prior to use, the unit will need to be configured to suit the end user.
If recording either via the onboard microphone or the line-in jack, the unit will need to be supplied with power.
WARNING
Important Note: For all versions, a source of DC power is required.
•
DC units (855H-R30C and 855H-RC30Cx) can be powered normally to complete recording and set-up.
•
AC units (855H-R45C and 855H-RC45Cx) must be temporarily powered from either a 12V battery or a
separate 10-30VDC isolated power supply, connected directly to the + and - DC terminals on the main PCB.
(Layout of main PCB is illustrated on page 5).
Disconnect from power source to prevent electrical shock before installing
or servicing. Check power supply voltage and frequency.
Déconnecter l'alimentation avant toute opération d'installation ou de maintenance,
afin d'éviter les décharges électriques. Controler la tension et la fréquence d'alimentation.
Schalten Sie den Strom während der Installation oder bei Wartungsarbeiten ab um
einen elektrischen Schlag zu vermeiden. Prüfen Sie die Spannung und Frequenz der Stromquelle.
Scollegare dall'alimentazione prima dell'installazione e della messa in servizio.
Controllare la tensione di alimentazione e la frequenza.
Desligar a alimentação antes de realizar qualquer intervenção. Verificar a tensão e
frequência da alimentação.
Durante el proceso de instalación o mantenimiento desconectar la tensión de
alimentación para evitar descargas eléctricas. Comprobar tensión y frecuencia de alimentación.
Current
190mA@12V
256mA@24V
256mA max@30V
112mA@120V
124mA@230V
127mA max@260V
110 dB (A) Tone
Risk of Electrical Shock. Disconnect from power source to prevent electrical
shock before servicing.
UL Type 4/4X/13/3R
855H Combined horn/LED units:
Catalog No.
Voltage Range
855H-RC30Cx
12-30V DC
855H-RC45Cx
90-260V AC
(50/60Hz)
Hearing protection required.
1
(Frame C)
IP66
Current
347mA@12V
413mA@24V
416mA max@30V
172mA@120V
159mA@230V
252mA max@260V
Advertisement
Table of Contents
Summary of Contents for AB Quality 855H Series
- Page 1 Bulletin 855H Recordable Horn (Frame C) 855H-R30C, 855H-R45C, 855H-RC30Cx, 855H-RC45Cx UL Type 4/4X/13/3R IP66 -20°C to +55°C (-4°F to +131°F) Disconnect from power source to prevent electrical shock before installing WARNING or servicing. Check power supply voltage and frequency. Déconnecter l’alimentation avant toute opération d’installation ou de maintenance, AVERTISSEMENT afin d’éviter les décharges électriques.
-
Page 2: Tone Selection
ACCESS TO PCB’S FOR PROGRAMMING AND POWER CONNECTIONS AC UNITS DC UNITS 4.5 lb-in (0.5 N•m) (2 places) 4.5 lb-in (0.5 N•m) 4.5 lb-in (4 places) (0.5 N•m) (4 places) AC UNITS: DC UNITS: 1. Remove 4 screws on face of unit to connect DC power Remove 4 screws on face of unit for access to DC for programming functions on Main PCB power connections and programming functions on Main PCB,... - Page 3 STAGE WIRING DC Units Stage 1 operation: Connect correct DC input voltage to "+" and "-" as appropriate. BEACON PRE-WIRED INTERNALLY DC Units Second, Third and Fourth Stage Selection Beacon The 855H Recordable Horn uses negative switching to change the tone to the second, third and fourth stages. The negative supply must remain WARNING connected to the...
-
Page 4: Mounting Dimensions
MOUNTING DIMENSIONS 144.0 144.0 130.0 126.0 126.0 130.0 130.0 130.0 133.5 133.5 Ø7.4 Ø7.4 86.4 86.4 86.2 BEACON 57.2 57.2 86.4 133.5 Ø7.4 Ø7.4 130.0 130.0 133.5 126.0 855H-R30C 130.0 126.0 86.2 144.0 BEACON 855H-RC30Cx 855H-R45C 86.4 130.0 144.0 126.0 855H-RC45Cx BEACON SET-UP The 855H Combo units will have the beacon already pre-wired to the unit so no extra wiring is required. -
Page 5: Main Pcb Layout
MAIN PCB LAYOUT Power & Alarm Stage Terminals for DC units (Also for DC Power to program AC units) Beacon pre-wired to ‘+’ and ‘-’ S2 - Set-up S4 - Tones (DC combo units only) Master/Slave Connector 4 5 6 Function LEDs ACTION RESET... - Page 6 855H RECORDABLE HORN QUICK START GUIDE This guide is designed to get the user quickly interfacing with the 855H Recordable Horn. • The unit can be set-up to either play an alarm tone followed by a recorded message, or just play the recorded message. •...
-
Page 7: Record Mode
RECORD MODE TO RECORD A MESSAGE ON STAGE 1 USING THE ON-BOARD MICROPHONE (NOTE: “Black” color indicates “ON” position) For Stage 1: Set dip switch S2 positions 2,3 & 4 to ‘ON’, all others to ‘OFF’ For Stage 2: Set Switch ‘S2’ positions 3 & 4 to ‘ON’;... -
Page 8: Playback Mode
PLAYBACK MODE (TO PLAY BACK A MESSAGE) (NOTE: “Black” color indicates “ON” position) For Stage 1: Set Switch ‘S2’ positions 1,2,3 & 5 to 'ON' Alternatively for : For Stage 2: Set Switch ‘S2’ positions 1,3 & 5 to 'ON’ For Stage 3: Set Switch ‘S2’... - Page 9 ERASE MODE - SINGLE STAGE (TO ERASE ONE STAGE AT A TIME) (NOTE: “Black” color indicates “ON” position) For Stage 1: Set Switch ‘S2’ positions 2,3 & 7 to 'ON' Alternatively: For Stage 2: Set Switch ‘S2’ positions 3 & 7 to 'ON' For Stage 3: Set Switch ‘S2’...
- Page 10 MASS ERASE MODE (ERASES ALL STAGES AT ONCE) (NOTE: “Black” color indicates “ON” position) Set Switch ‘S2’ position 7 to 'ON' Set jumper J4 ‘ME’ to ON position (centre and right pin connected) Switch on power or Press reset button Press action button: Erase will begin - - - - erase complete...
- Page 11 SYNCHRONIZING TWO SOUNDERS (ALL STAGES) THIS FUNCTION WILL ALLOW MULTIPLE UNITS TO BE SET UP EXACTLY THE SAME AS A PREDETERMINED “MASTER” UNIT Connect Synch cable to Master and Slave PCB Designate one unit as Master and one unit as Slave On both units: Set jumper J6 (SYNC) to ON Set jumper J5 (S/M) on Master...
- Page 12 TONE SE E LECTIO O N TABLE E Switch Stage 2 Stage 3 Stage 4 1 2 3 4 5 6 Stage 1 Frequency Description (S2) (S3) (S4) 340 Hz Continuous Tone 1 Tone 2 Tone 5 Tone 29 Tone 2 800/1000 Hz @ 0.25 sec Alternating Tone 17 Tone 5...