Lifetime COMPETITION Series XL POWER LIFT 71525 Assembly Instructions And Owner's Manual
Basketball system
Hide thumbs
Also See for COMPETITION Series XL POWER LIFT 71525:
- Assembly instructions manual (48 pages)
Advertisement
Quick Links
3/31/2012
®
www.lifetime.com
**U.S. and Canada customers ONLY**
IF ASSISTANCE IS NEEDED,
DO NOT CONTACT THE STORE!
CALL OUR CUSTOMER SERVICE DEPARTMENT
1 (800) 225-3865
at
HOURS: 7:00 a.m. to 5:00 p.m. Monday through Friday (Mountain Standard Time)
**Call or visit our Web site for Saturday hours**
**For customers outside the U.S. or Canada, please contact the store for assistance.**
®
COMPETITION SERIES XL POWER LIFT
BASKETBALL SYSTEM
MODEL #71525
WARNING
Failure to comply with any of the warnings
ASSEMBLY INSTRUCTIONS AND OWNER'S MANUAL
in these instructions may result in serious
personal injuries such as cuts, broken bones,
nerve damage, paralysis, brain injury, or
death. Failure to comply may also result in
property damage. Please heed all warnings
and cautions. To ensure your safety, do not
**A MINIMUM OF TWO ADULTS ARE REQUIRED FOR
attempt to assemble this system without
ASSEMBLY**
reading and following all instructions carefully.
Identify and inventory the parts using the
Parts List.
Save this instruction in the event that the manufacturer has to be contacted for replacement parts.
INSTRUCTION #1039811 D
1
Advertisement
Related Manuals for Lifetime COMPETITION Series XL POWER LIFT 71525
Summary of Contents for Lifetime COMPETITION Series XL POWER LIFT 71525
- Page 1 3/31/2012 ® www.lifetime.com **U.S. and Canada customers ONLY** IF ASSISTANCE IS NEEDED, DO NOT CONTACT THE STORE! CALL OUR CUSTOMER SERVICE DEPARTMENT 1 (800) 225-3865 HOURS: 7:00 a.m. to 5:00 p.m. Monday through Friday (Mountain Standard Time) **Call or visit our Web site for Saturday hours** **For customers outside the U.S.
- Page 2 HARDWARE IS ACTUAL SIZE PARTS LIST (Unless otherwise indicated) Part # Description 1030700 Top Pole 1030701 Middle Pole 1030859 Bottom Pole DD00800 502027H Handle 502049G Trigger 1030667 Extension Arm (Long) (Not actual size) 1030669 Extension Arm (Short) 502056 Plastic Guard CA00885 Zip Tie 604084...
- Page 3 PARTS LIST HARDWARE IS ACTUAL SIZE (Unless otherwise indicated) Part # Description Thread lengths may vary Handle Hardware (1017923) 302007 3/8” x 6 1/2” Hex Bolt 300101 Release Pin 302008 3/8” Centerlock Nut 300187 1/2” x 6 1/2” Hex Bolt 301008 1/2”...
- Page 4 Maintaining your privacy is our long-standing policy at Lifetime. And you can rest assured that Lifetime will not sell or provide your personal data to other third parties, or allow them to use your personal data for their own purposes.
- Page 5 For a nonpermanent installation of your basketball system, a Ground Sleeve provides an alternative to 2.1 Mix 5 1/2 bags of concrete, following the directions on the concrete bags. cementing the pole into the ground. See Page 14 for more information. Keep in mind that a thicker mix of concrete will dry stronger.
- Page 6 7.1 Apply the Height Sticker (AL) so it wraps 6.1 Completely tighten the Nuts. 8.1 Align the hole in the Top Pole with the Required For This Page: around the opposite side of the pole as the slot in the Middle Pole and slide the Top 9/16”...
- Page 7 Required For This Page: HD (1) 11.1 Line up the Rear Lifter Arms 13.1 Tighten the Nut until it is flush with 12.1 Use pliers to bend the (AR) with the Gas Spring (AN). Cotter Pin (MD) as shown the Bolt. 1017923 above.
- Page 8 Required For This Page: 17.1 Hold the Backboard 19.1 Insert a 5/16” x 2” 20.1 Use the 1/2” socket 18.1 Ensure the U-Bolt (RE) Brackets (AP & AQ) together Carriage Bolt (RC) through head from the socket head is in the notches. and slide the U-Bolt (RE) through the each hole in the Rim Pivot Bracket wrench to press one Push Nut (RB)
- Page 9 Required For This Page: 23.1: Slide a Spacer (MC) over each Tap Bolt (RC) between 24.1 Place the Compression 25.1 Place the Spring Retainer Plate the Backboard and the Backboard Brackets. Springs (RG) over the ends of (RJ) and secure with Nylock Flange the U-Bolt (RE).
- Page 10 Required For This Page: 28.1 Bend the Backboard Brackets (AP & AQ) out 29.1 Tighten the Nut until it is flush with the Bolt. and over the Carriage Bolt (MX). 1/2” Wrench 3/4” Wrenches 1039829 Note: The lower holes should go over the Carriage Bolts.
- Page 11 32.1 Remove the plastic film from the 33.1 Lift the pole up until the Long Extension Arms (AE) line up with the holes in the Required For This Page: Backboard. Rear Lifter Arms (AR). 3/4” Wrenches 1/2” Socket Wrench Hammer/Mallet Electric Drill 1039829 33.2 Only finger tighten the Nut.
- Page 12 36.1 Attach the Net (AB). 37.1 Apply the Grease (MQ) to these areas. Note: Please call our Customer Service Department at the number on Page One to obtain replacement Nets. Our CAUTION: DO NOT APPLY EXCESSIVE WEIGHT TO THE HANDLE. Do not hang anything from the Handle, as this will damage the system and void the product warranty.
- Page 13 Required For This Page: **AT LEAST 2 ADULTS REQUIRED FOR THIS STEP** Screwdriver Hammer/Mallet 39.1 Ensure the Backboard faces the playing surface and align the small hole in the Middle Pole (MP) with the correct slot in the Bottom Pole (BP). Electric Drill Slide the Middle Pole over the Bottom Pole.
- Page 14 Operation of the height adjustment system The adjustable system may be adjusted from 7 1/2 feet to 10 feet. Hold the Handle tightly and squeeze the Trigger to engage the Gas Spring. Raise the Handle to lower the Backboard, or lower the Handle to raise the Backboard.
- Page 16 This warranty is nontransferable and is expressly limited to the repair or replacement of defective basketball equipment. If the equipment is defective within the terms of this warranty, Lifetime Products, Inc. will repair or replace defective parts at no cost to the purchaser. Shipping charges to and from the factory are not covered and are the responsibility of the purchaser.
Need help?
Do you have a question about the COMPETITION Series XL POWER LIFT 71525 and is the answer not in the manual?
Questions and answers