Table of Contents
Advertisement
Heat Selector Switches (see Fig.3)
Heat selection is provided via a rotary switch offering four
settings. The heat output can be altered to suit the application,
conditions and for improve the economy of operation.
Available output options are as follows:
Model
O
ECR15(Ti(e))
Off
ECR20(Ti(e))
Off
Timer Models
DIGITAL TIMER
(Tie models)
ON
OFF
IMPORTANT: Remember to observe all safety warnings
when operating the heater on auto setting, either attended or
unattended.
The timer allows you to select 'AUTO' or 'MAN ON' by pressing
the 'MODE' button until the required MODE appears at the
bottom of the timer display.
'AUTO' MODE allows the heater to switch ON and OFF
according to a set 24 Hour program period (see 'Setting
Programs' section below).
'MAN ON' MODE allows power to the heater uninterrupted by
the program settings.
Key Lock
If 'ENTER' and 'MODE' are pressed within 1 second, the keys
will be locked. The user will know the keys are locked as the
lock symbol ' ' will be displayed on the top left hand corner
of the screen. To unlock the keypad, press 'ENTER' and then
'MODE' within 1 second.
.
Initial Operation
For initial use, plug the heater into a regular household power
point and turn the power on. The timer is now ready to be set
up for use.
Switch setting
I
II
500W
1000W
600W
1400W
P1
MANUAL ON
13 : 17
AUTO
ADVANCE
Fig. 4
Setting Current Time
1. Hold the 'PROGRAM' button until the clock symbol
appears on the screen. The user can now set the clock.
2. The hour digit will flash. To adjust the hour use the '-' &
'+' buttons. Confirm the hour digit by pressing 'ENTER'.
3. Once 'ENTER' has been pressed the minutes will flash.
To adjust the minutes use the '-' & '+' buttons. Confirm
III
the minute digit by pressing 'ENTER'.
4. The timer now returns to the default display.
1500W
5. To reset incorrect time, repeat previous steps.
2000W
Once the correct time is set, a total of four ON/OFF time
programs can be set for operation.
Setting Programmes
Press the 'PROGRAM' key to set the programs.
You are now setting the programs starting with P1 'ON'.
SETTING P1 ON TIME
1. To set the hour use the '-' & '+' buttons. Confirm the
hour digit by pressing 'ENTER'.
2. To set the minutes use the '-' & '+' buttons. Confirm
the minute digit by pressing 'ENTER'.
Note: The minutes can only be set in 10 minute blocks in
programme 'MODE'.
SETTING P1 OFF TIME
3. To set the hour use the '-' & '+' buttons. Confirm the
hour digit by pressing 'ENTER'.
4. To set the minutes use the '-' & '+' buttons. Confirm
the minute digit by pressing 'ENTER'.
Repeat steps 1 to 4 to programme P2, P3 & P4. After
programming P4 'OFF' you automatically exit to the default
display.
At any time while programming the timer you can press the
'PROGRAM' button to exit to the default display.
Note: If the 'ON' time is the same as the 'OFF' time the appliance
will ignore the program.
The Advance Function
When in 'AUTO' MODE, if the '+' button is pressed for longer
than 2 seconds the programme will ADVANCE to the next
setting programmed and will only revert back to the program
when the subsequent programme time is reached. When the
'ADVANCE' function is running the 'ADVANCE' segment will
be displayed on the LCD screen. If the '-' button is pressed
when the 'ADVANCE' programme is running the 'ADVANCE'
feature will be automatically cancelled and the programme will
run as normal.
Note - Timer Memory Back Up Batteries - Once the heater has
been left plugged in with the socket switched on for at least
72 hours the timer's memory back up batteries will be fully
charged.
Once the timer batteries are fully charged, if there is a power
cut or if the heater is disconnected from the mains for less than
Advertisement
Table of Contents
