Advertisement
Quick Links
Advertisement
Related Manuals for EnGenius ESR-1221N
Summary of Contents for EnGenius ESR-1221N
- Page 1 EnGenius Gold 11N Wireless Router V1.0...
- Page 2 ...7 ...7 ...7 ...8 ...9 ...10 ...11 ...14 ...16 ...17 ...20 ...32 ...32 ...36 ...40 ...43 ...45 ...10 ...11...
- Page 3 ...46 ...47 ...48 ...48 ...49 ...51 ...52 ...54 ...54 ...57 ...59 ...65 ...67 ...70 ...71 ...72 ...72 ...73 ...74 ...75...
- Page 4 ...76 ...77 ...78 ...79 ...80 ...81 ...82 ...85 ...87 ...87 ...88 ...89 ...90 ...91 ...92 ...93 ...79 ...83 ...84 ...89...
-
Page 5: Table Of Contents
...94 ...95 Appendix B – Industry Canada statement ...97 IMPORTANT NOTE: ...102 End Product Labeling ...102 Plaque signalétique du produit final...103 Manual Information To the End User...103... - Page 8 1. Introduction • • • • • • • • •...
- Page 12 2. Configure PC/Laptop Network Interface Windows XP Windows Vista...
- Page 13 Windows Vista, click [View Network Status and Tasks] then [Manage Network Connections]...
- Page 16 Internet Protocol Version 4 (TCP/IPv4) Properties Button...
- Page 18 3. Setup your Router...
- Page 21 4. Manually enter Setup Wizard Note:...
- Page 25 AP Router Mode...
- Page 31 Note:...
- Page 33 5. System...
- Page 49 6. Internet...
- Page 54 PPP over Ethernet (PPPoE) Username: Password: Service: MTU: Authentication type Auto Type: Keep Connection: Automatic Connection: Manual Connection: Connect Idle Timeout: Automatic Connection...
- Page 55 7. Wireless...
- Page 57 To create a WDS network, please enter the MAC addresses of the Access Points that you want included in the WDS. There can be a maximum of four access points.
- Page 61 • • • • • • • • •...
- Page 63 • •...
- Page 73 8. Firewall...
- Page 75 • • • Note:...
- Page 80 9. Advanced...
- Page 86 Note:...
- Page 87 Destination Subnet Mask Gateway Interface...
- Page 88 10. Tools...
- Page 90 Virtual Server...
- Page 93 Upgrade File Note:...
- Page 96 Appendix A – FCC Interference Statement...
-
Page 98: Appendix B - Industry Canada Statement
Appendix B – Industry Canada statement This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. - Page 99 The band from 5600-5650MHz will be disabled by the proprietary software during the manufacturing and which cannot be changed by the end-user. French translation: NOTE IMPORTANTE: (Pour l'utilisation de dispositifs mobiles) Déclaration d'exposition aux radiations: Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé...
- Page 100 (The user manual of transmitter devices equipped with detachable antennas shall contain the following information in a conspicuous location: ) This device has been designed to operate with an antenna having a maximum gain of [x] dB. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada.
- Page 101 lapuissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire àl'établissement d'une communication satisfaisante. IMPORTANT NOTE: (For Portable device use) Radiation Exposure Statement: The product comply with the US/Canada portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual.
- Page 102 This device is intended only for OEM integrators under the following conditions: (For module device use) 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna, For all products market in Canada, OEM has to limit the operation channels in CH1 to CH11 for 2.4G band by supplied firmware programming tool.
-
Page 103: Important Note
In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used on the final product. -
Page 104: Plaque Signalétique Du Produit Final
Plaque signalétique du produit final Ce module émetteur est autorisé uniquement pour une utilisation dans un dispositif où l'antenne peut être installée de telle sorte qu'une distance de 20cm peut être maintenue entre l'antenne et les utilisateurs. Le produit final doit être étiqueté...