Table of Contents
Advertisement
Pos : 7 /T ec hnis che D okumentati on/Betriebs anl eitung en/Allgemein/Sic her hei tshi nweis e_FSE @ 10 \mod_1390378407459_48.doc x @ 118163 @ 122 @ 1
Safety Instructions
Read these operating instructions carefully before working with the radio system. This applies in particular
to the installation, commissioning and maintenance of the radio system.
The operating instructions are a constituent part of the radio control sys tem and must always be kept close
at hand for the responsible personnel.
The term 'machine' is used in the operating instructions for the different possible uses of the radio system.
Intended Use
The radio system is used for the control of machines and for data transfer. Observe the occupational
safety and accident prevention regulations applicable to each application.
The intended use also includes reading the operating instructions and adhering to all safety information
contained therein.
The radio system must not be used in areas where there is a risk of explosion, nor for the control of
machines used to convey persons, unless it is explicitly approved for these uses by the manufacturer.
Modifications to the radio system may only be carried out by speci alist personnel who have been
trained and authorized by HBC-radiomatic. All modifications must be documented at the factory in the
radio control master file.
The safety devices of the radio control system must not be modified, removed or bypassed. In
particular, modifications to any part of the radio system's complete E-STOP system are not allowed.
Safety Instructions for Installation and Operation
The electrical connection according to the enclosed output wiring diagram must be established by a
qualified electrician exclusively.
The receiver may only be opened by trained personnel. Components in side the receiver can be
energized at life-threatening voltages. The supply voltage for the machine must be disconnected
before the receiver is opened.
The power supply of the machine control as well as the contacts for external switching devices may
only be connected to electrical circuits that have an all-pole separation device. (One separation device
for the power supply and at least one separation device for the external switching devices.)
For bus systems, the electronics of the machine needs to examine all control commands that belong
to the Safety Circuit 2 for plausibility using the Si -2 hardware output on the side of the radio; in case
there are implausibilities, it has to initiate the safe state immediately.
Please also note that, with radio systems, the presence of persons in the danger zone – in particular
beneath the load (cranes!) – is prohibited in all cases.
Select a safe location for radio control, from which you have a good and complete view of the working
movements of the machine, the load movements and the surrounding working conditions.
It is not permissible to leave a radio transmitter unattended while it is activated. Always switch off the
radio transmitter when it is not needed. This applies in particular if you change location, when working
without radio control, during breaks and at the end of work. Always protect the radio transmitter against
use by unauthorized persons, for example by locking it away.
In the event of an emergency and with all faults, switch off the radio transmitter immediately by
pressing the STOP switch.
Only operate the radio system when it is in perfect working order. Faults and defects that could
influence safety must be rectified by specialists who have been trained and authorized by HBC-
radiomatic before the system is put back into operation.
Note that the operational directions of the operating elements may appear inverted depending on
location and viewing angle to the machine. This applies in particular to rotary cranes if your location
changes from inside to outside the radius of the crane. The operator must make himself familiar with
the directional markings on the machine before starting to work.
Repairs may only be carried out by specialist personnel wh o have been trained and authorized by
HBC-radiomatic. Use original replacement parts and accessories (e.g. rechargeable batteries)
exclusively; otherwise it is possible that the equipment safety can no lo nger be guaranteed and our
extended warranty will be voided.
Remain vigilant when working with the radio system and familiarize yourself with its functions. This
applies in particular if you are working with it for the first time or if you work with it on ly occasionally.
Pos : 10 /T echnisc he Dokumentation/Betriebsanl eitungen/Allgemei n/----- Sei tenumbr uch ------ @ 1\mod_1219672326234_0.doc x @ 29509 @ @ 1
3 / 13
Hide quick links:
Advertisement
Table of Contents
