Subscribe to Our Youtube Channel
Related Manuals for ATD Tools ATD4P8D
Summary of Contents for ATD Tools ATD4P8D
- Page 1 ATD4P8D & ATD4P8DXL Four Post Storage Lifts 8,000 lbs. Capacity (4,000 lbs. per axle) INSTALLATION / OWNERS MANUAL Jun 2017...
-
Page 2: Table Of Contents
Any other proposed application of this equipment should be documented and submitted in writing to the factory for examination. The user assumes full responsibility for any equipment damage, personal injury, or alteration of the equipment described in this manual or any subsequent damages. ATD4P8D / ATD4P8DXL Jun 2017... -
Page 3: Lift Specifications
80” 87.2 Locking Positions Base Plate Size 10” x 12” 10” x 12” Power 110V-15 Amp / 1PH 110V-15 Amp / 1PH Ship Weight 1,695 lbs. 1,805 lbs. FLOOR PLAN LAYOUT (ATD4P8D) (ATD4P8DXL) (ATD4P8D) (ATD4P8DXL) ATD4P8D / ATD4P8DXL Jun 2017... - Page 4 (ATD4P8D) (ATD4P8DXL) 80.00” (ATD4P8D) 87.20” (ATD4P8DXL) ATD4P8D / ATD4P8DXL Jun 2017...
-
Page 5: Tools Required
DO NOT install lift close to wall. It is necessary to leave adequate clearance for safe movement around lift. Suggested clearance to be 1 meter (3 feet) minimum. OPERATING CONDITIONS: Lift is not intended for outdoor use and has an operating ambient temperature range of 41º-104ºF (5º-40ºC). ATD4P8D / ATD4P8DXL Jun 2017... -
Page 6: Main Components & Accessory Identification
OPTIONAL ACCESSORIES NOT SHOWN: • ATDSJ3500 Sliding Scissor Jack – 3,500 lbs. capacity • Aluminum Drive-On Ramps • 90 Degree Power Unit Bracket Kit (only to the rear of Mainside Column for ATD4P8D & ATD4P8DXL Lifts) ATD4P8D / ATD4P8DXL Jun 2017... -
Page 7: Installation Instructions
Cylinder Hose ‘Wire braided’ Hose 90 degree Fitting w/ Jam Nut Fig. 2 4. Fully extend the Cylinder Piston Rod by pushing or pulling on the Cable Lock Plates mounted on the end of the Cylinder. ATD4P8D / ATD4P8DXL Jun 2017... - Page 8 Remove the Safety Latch covers (#14) from Crossbeams. They will be reinstalled later. Arrange the Crossbeams so that the Latches’ Linkage Rods are facing outward and the Short Rod (#70) is closest to the Power Unit Column, as shown below in Fig.3. Short Rod Fig. 3 ATD4P8D / ATD4P8DXL Jun 2017...
- Page 9 Washer and Nut as shown in Fig 4b. Note: Ensure Jam Nut is positioned below Top Caps. Position the Crossbeams at Lock Ladder the second lowest locking position on all columns Fig. 4 ATD4P8D / ATD4P8DXL Jun 2017...
- Page 10 Fig. 5 & 5b. The lift will square itself as you further assemble it. Note: Ensure to install the ‘offside’ Sub Runway opposite from the Main side Runway and Power unit Column, as shown in Fig.5b. Mounting Plate Sub Runway Mainside Runway Fig. 5 Fig. 5b ATD4P8D / ATD4P8DXL Jun 2017...
- Page 11 Fig. 7. Four Guide Bolts will be installed at one end and two at the other end. Note: Cable Guide Bolts assists in keeping the Cables properly engaged to the Pulleys. Fig. 7 ATD4P8D / ATD4P8DXL Jun 2017...
- Page 12 (#69) to outside / middle of each Crossbeam, secure each Eye bolt with Hex Nut. Note: Ensure the ‘front to back’ Linkage Rods are properly routed through guide ring weldments, located on the underside of the Mainside Runway. (Also see Exploded View Details on Page 24) Fig. 9 ATD4P8D / ATD4P8DXL Jun 2017...
- Page 13 Each Column has this adjustment. Adjust the proper columns to level the lift. Place a level on each runway and crossbeam and check for proper levelness. Note: You may have to loosen the Jam Nut under the Top Cap to make adjustments. ATD4P8D / ATD4P8DXL Jun 2017...
- Page 14 31. Install the Jack / Tool Tray & Drip Trays between the Runways. NOTE: Ensure to lubricate ALL Cable Sheaves, Bearings and Shafts with grease prior to operating Lift. The Lift installation is now complete. ATD4P8D / ATD4P8DXL Jun 2017...
-
Page 15: Caster Kit Assembly / Installation
5. Lower the Lift confirming that the Caster assemblies engage the columns and all four Columns rise to clear the floor. 6. Now the lift can be moved. CAUTION: DO NOT maneuver Lift with Casters, while vehicle is on Lift. Read Safety & Operation Instructions before operating Lift. ATD4P8D / ATD4P8DXL Jun 2017... -
Page 16: Foundation & Anchoring Requirements
Run nut down just Tighten nut with carbide tipped below impact section Torque wrench to masonry drill bit per of bolt. Drive anchor 130 ft.-lbs. ANSI standard into hole until nut and B94.12.1977 washer contact base. ATD4P8D / ATD4P8DXL Jun 2017... -
Page 17: Safety Instructions & Procedures
Motors and all electrical components are not sealed against the weather and moisture. Install this lift in a protected indoor location. Failure by the owner to provide the recommended shelter could result in unsatisfactory lift performance, property damage, or personal injury. ATD4P8D / ATD4P8DXL Jun 2017... -
Page 18: Operation Instructions
UNDER THE VEHICLE. NEVER ALLOW ANYONE TO GO UNDER THE LIFT WHEN RAISING OR LOWERING. NOTE: It is normal for an empty lift to lower slowly - it may be necessary to add weight. Read and adhere to all WARNING, CAUTION and SAFETY INSTRUCTIONS labels on lift. ATD4P8D / ATD4P8DXL Jun 2017... -
Page 19: Preventive Maintenance Schedule
Check for excessive wear of cable. Replace them if necessary. Change the hydraulic fluid - operating temperature, type of service, contamination levels, filtration, and chemical composition of fluid should be considered. If operating in dusty environment shorter interval may be required. ATD4P8D / ATD4P8DXL Jun 2017... -
Page 20: Troubleshooting
1. Cross beam ends are rubbing the columns. Readjustment needed. 2. Cylinder too tight. Load lift to half capacity and cycle up and down a few times to break in. 3. May have excessive wear on cable sheaves or shafts. Replace them. ATD4P8D / ATD4P8DXL Jun 2017... -
Page 21: Power Unit Priming Procedure
POWER UNIT PRIMING PROCEDURE WARNING!! Failure to properly relieve pressure in the following steps can cause injury to personnel. Step 1 - Locate the check valve. It is the plug to the left of the lowering valve. ATD4P8D / ATD4P8DXL Jun 2017... -
Page 22: Latch & Cable Inspection / Adjustments
Latches may not click in at the same time when vehicle is being raised but should be close. Be sure all four corners have passed the locking latch bar slot before lowering lift on locking latches. ATD4P8D / ATD4P8DXL Jun 2017... - Page 23 yW>K s/ t ATD4P8D / ATD4P8DXL Jun 2017...
- Page 24 yW>K s/ t ATD4P8D / ATD4P8DXL Jun 2017...
- Page 25 yW>K s/ t ATD4P8D / ATD4P8DXL Jun 2017...
- Page 26 yW>K s/ t ATD4P8D / ATD4P8DXL Jun 2017...
- Page 27 yW>K s/ t ATD4P8D / ATD4P8DXL Jun 2017...
- Page 28 &W < ^ y y>d dd &W < ^ y y>d dd > > >, &W < ^ y y>d dd > > &W < ^ y y>d > &W < ^ y y>d ATD4P8D / ATD4P8DXL Jun 2017...
- Page 29 &W < ^ y y>d &W < ^ < &W < ^ y W& > ^ y &W < ^ y y>d W& &W < ^ y y>d W& &W < ^ y y>d W& > > ATD4P8D / ATD4P8DXL Jun 2017...
- Page 30 &W < ^ y y>d &W < ^ y y>d & &W < ^ y y>d W& & &W < ^ y y>d &W < ^ y y>d W& &W < ^ y y>d d W y> ATD4P8D / ATD4P8DXL Jun 2017...
- Page 31 &W < ^ y y>d &W < ^ y y>d &W < ^ y y>d &W < ^ y y>d &W < ^ y y>d &W < ^ y y>d &W < ^ y y>d ATD4P8D / ATD4P8DXL Jun 2017...
- Page 32 ATD4P8D / ATD4P8DXL Jun 2017...
Need help?
Do you have a question about the ATD4P8D and is the answer not in the manual?
Questions and answers