Download Print this page
Elmo TND4104X Instruction Manual

Elmo TND4104X Instruction Manual

Color ccd tv camera
Hide thumbs Also See for TND4104X:

Advertisement

Quick Links

I N S T R U C T I O N M A N U A L
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended to alert the user
to the presence of uninsulated "dangerous
voltage" within the product's enclosure that may
be of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and maintenance
(servicing) instructions in the literature
accompanying the appliance.
CAUTION
Do not use any power supply other than
specified.
WARNING
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
* The CAUTION label is attached on the
bottom of camera.
T N D 4 1 0 4 X
D O M E C A M E R A
INFORMATION
This equipment has been tested and found
to comply with the limits for Class A digital
device, pursuant to Part 15 of the FCC
Rules. These limits are designed to
provide reasonable protection against
harmful interference when the equipment
is operated in a commercial environment.
This equipment generates, uses, and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instruction manual, may cause harmful
interference to radio communications.
Operation of this equipment in a
residential area is likely to cause harmful
interference in which case the user will be
required to correct the interference at his
own expense.
USER-INSTALLER CAUTION:
authority to operate this FCC verified
equipment could be voided if you make
changes or modifications not expressly
approved by the party responsible for
compliance to Part of the FCC Rules.
Your

Advertisement

loading

Summary of Contents for Elmo TND4104X

  • Page 1 T N D 4 1 0 4 X D O M E C A M E R A I N S T R U C T I O N M A N U A L CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).
  • Page 2: Important Safety Instructions

    IMPORTANT SAFETY INSTRUCTIONS Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings, install in accordance with the manufacturer's instructions. Do not install near heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat.
  • Page 3: Name And Function Of Each Part

    Name and Function of Each part Name The main body of the camera section. Main body For adjusting the image size. Zoom ring For adjusting the focus. Focus ring Cover lens Protective cover for the lens. Dome cover main body Protective cover for the main body.
  • Page 4 Name Screw hole for For fixing the main body with screws. mounting main body AW PUSH Used when the white balance is in the PUSH mode. DOWN/UP For setting the vertical sync. phase. ALC adjustment volume For adjusting the brightness of the image. Tilt lock screw For locking the tilt after adjusting the image up/down direction.
  • Page 5 Selector switch (Details) 1.SENS UP switch To set the max. value (upper limit value) of the operating gain in the auto gain control circuit, set this switch to ON position. In case the back lighting is too dark and the camera sensitivity is insufficient, set this switch to ON position.
  • Page 6: How To Install

    How to Install 1. Make holes in the mounting surface. (Fig. 1)(Fig. 2) 2. Unscrew the dome cover screw and dome cover main body mount screw (Fig. 3). Be careful not to drop any of the dome cover screw and dome cover main body mount screw.
  • Page 7 4. Fasten the main body to the ceiling/wall surface/box with a main body mount screw (Figs. 4). Make sure that it is fixed firmly. Make sure of the position of the front of the camera. Weight of the main body and mounting metal piece is 650 g.
  • Page 8 6. Correct the tilting of the image (Fig. 7). Be sure to hold the cover motor. 7. Install the cover lens (Fig. 8). 8. Mount the dome cover main body by matching the dome cover main body mount screw with the mark on the main body and turning it clockwise (arrow direction) (Fig.
  • Page 9 When any failure is suspected Symptoms Image is not displayed. Are cables connected correctly? Are the power plugs of peripheral units inserted correctly into the receptacles? Is the video monitor adjusted correctly? Color is not correct. Is any connector of this machine or video monitor loose or Image is disarrayed.
  • Page 10 Appearance All dimensions in mm(inch) 162(6.38) 101.6(4.00)
  • Page 11: Specifications

    VIDEO OUT terminal Lens Angle of view Dimensions Weight Ambient temperature Ambient humidity Accessory TND4104X AC24V(AC15V-27V) 60Hz 0.5Hz or DC12V(DC11V-35V) AC : Approx.2.5W or DC : Approx.2.8W 1/3" color interline-transfer CCD 768(H)X494(V) 4.88mm(H)X3.66mm(V) 2:1interlaced LL : 15.75kHz (H), 60Hz (V) INT : 15.734kHz (H), 59.94Hz (V)
  • Page 12 ELMO COMPANY, LIMITED. ELMO CO., LTD. OVERSEAS SUBSIDIARY COMPANIES ELMO Mfg. Corp. ELMO Canada Mfg. Corp. 1478 Old Country Road, 44 West Drive, Brampton, Plainview, NY 11803-5034 Ontario, L6T 3T6, U.S.A. Canada Tel. 516-501-1400 Tel. 905-453-7880 Fax.