Table of Contents
Advertisement
Quick Links
© 2007 CLEMCO INDUSTRIES CORP.
One Cable Car Dr.
Washington, MO 63090
Phone (636) 239-4300
F
(800) 726-7559
ax
Email: info@clemcoindustries.com
www.clemcoindustries.com
CLIMATE CONTROL TUBE
MODEL CCT
O. M. 08850
MC FILE NUMBER:
DATE OF ISSUE:
REVISION:
WARNING
Do not proceed with
these instructions until
you have READ the
orange cover of this
MANUAL and YOU
UNDERSTAND its
contents. *
These WARNINGS are
included for the health
and safety of the
operator and those in
the immediate vicinity.
*If you are using a Clemco Distributor
Maintenance and Part Guide, refer to
the orange warnings insert preceding
the Index before continuing with the
enclosed instructions.
Electronic files include a Preface
containing the same important
information as the orange cover.
629-1284
12-21-84
E, 05-07
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Clemco CCT
Summary of Contents for Clemco CCT
- Page 1 © 2007 CLEMCO INDUSTRIES CORP. One Cable Car Dr. *If you are using a Clemco Distributor Washington, MO 63090 Maintenance and Part Guide, refer to Phone (636) 239-4300 (800) 726-7559 the orange warnings insert preceding Email: info@clemcoindustries.com...
-
Page 2: General Instructions
DO NOT modify or substitute any Clemco parts with other The products described in this material may be combined by types or brands of equipment. Unauthorized modification... - Page 3 ALWAYS attach safety cables at ALL air hose AND blast 1910.244). hose coupling connections. Cables relieve tension on hose and control whipping action in the event of a coupling blow-out. • NEVER modify OR substitute remote control parts. Parts from different manufacturers are NOT compatible with Clemco...
-
Page 4: Maintenance
• Training and Educational Programs. free of the rightful claim of any third party by way of patent Clemco Industries Corp. offers a booklet, Blast-Off 2, infringement or the like. developed to educate personnel on abrasive blast equipment 6. This warranty is conditioned upon seller’s receipt within ten function and surface preparation techniques. - Page 5 PREFACE □ □ 3. Clean, properly maintained NIOSH-APPROVED 8. BLAST HOSE with ID 3 to 4 times the nozzle orifice. SUPPLIED-AIR RESPIRATOR. ALL components should Lines MUST be run AS STRAIGHT AS POSSIBLE from ALWAYS be present. NEVER operate without inner lens in machine to work area with NO sharp bends.
- Page 6 CAUTION Caution indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. © 2007 CLEMCO INDUSTRIES CORP. • www.clemcoindustries.com • Manual No. 08850...
-
Page 7: Air Supply
Read the entire titled Commodity Specification For Air, published by manual before installing or operating the equipment. Compressed Gas Association Inc., Chantilly, VA. Website: www.cganet.com, (29 CFR 1910.134 (i) © 2007 CLEMCO INDUSTRIES CORP. • www.clemcoindustries.com • Manual No. 08850... - Page 8 Section 2.4.3. and (i) and 49 CFR part 173, and part 178. Maintaining the correct operating pressure at the point of attachment ensures the correct air flow to the respirator. © 2007 CLEMCO INDUSTRIES CORP. • www.clemcoindustries.com • Manual No. 08850...
-
Page 9: Setup And Adjustments
The climate control tube must be supplied with 20 cfm of Grade D breathing air at 90 to 100 psi. 3.1.3 Attach an approved Clemco respirator hose to the quick-disconnect nipple. © 2007 CLEMCO INDUSTRIES CORP. • www.clemcoindustries.com • Manual No. 08850... -
Page 10: Service & Maintenance
Remove the o-ring from lower valve plate. climate control tube and inspect the screen for blockage. NOTE: If the lower plate and pin come loose, refer to Figure 4 for reassembly. © 2007 CLEMCO INDUSTRIES CORP. • www.clemcoindustries.com • Manual No. 08850... - Page 11 Make sure the hot-end Replace if necessary. If only cleaning is required, carefully orifice is on the breaker end of the tube. clean the slots with a brush or small screwdriver. Clean © 2007 CLEMCO INDUSTRIES CORP. • www.clemcoindustries.com • Manual No. 08850...
- Page 12 Vortex Tube Spacer 1, Thin Venturi Tube Spacer, Thick Venturi Venturi O-Ring Support Washer Spring Washers Convex sides must face each other Threaded Retainer Figure 5 © 2007 CLEMCO INDUSTRIES CORP. • www.clemcoindustries.com • Manual No. 08850...
-
Page 13: Troubleshooting
• Periodically move the temperature control lever toward the cooler position to defrost the tube • Lower the outlet temperature enough to keep exhaust air from freezing. © 2007 CLEMCO INDUSTRIES CORP. • www.clemcoindustries.com • Manual No. 08850... - Page 14 Venturi tube ..........08967 NOTE: If items 1 and 2 are ordered together, you Spacer 2, thick ..........08968 will receive an extra cool end venturi o-ring. Threaded retainer ........08829 Figure 6 © 2007 CLEMCO INDUSTRIES CORP. • www.clemcoindustries.com • Manual No. 08850...
Need help?
Do you have a question about the CCT and is the answer not in the manual?
Questions and answers