Clemco 600 Manual
  1. Manuals
  2. Brands
  3. Clemco Manuals
  4. Respiratory Product
  5. 600
  6. Manual

Clemco 600 Manual

Apollo supplied-air respirator
Hide thumbs Also See for 600:
Table of Contents

Advertisement

Quick Links

Download this manual
NOTICE
This supplied air respirator conforms to all NIOSH
specifications and standards and carries NIOSH
approval.
As
manufactured,
complies only with those foreign approvals that
accept NIOSH certification. Specifically, it has not
been manufactured to European
and does not carry the European
© 2014 CLEMCO INDUSTRIES CORP.
One Cable Car Dr.
Washington, MO 63090
Phone (636) 239-4300
F
(800) 726-7559
ax
Email: info@clemcoindustries.com
www.clemcoindustries.com
APOLLO SUPPLIED-AIR RESPIRATOR
DATE OF ISSUE:
REVISION:
Do not proceed with
these instructions until
you have READ the
orange cover of this
MANUAL and YOU
UNDERSTAND its
contents. *
These WARNINGS are
this
respirator
included for the health
and safety of the
standards
mark.
operator and those in
the immediate vicinity.
*If you are using a Clemco Distributor
Maintenance and Part Guide, refer to
the orange warnings insert preceding
the Index before continuing with the
enclosed instructions.
Electronic files include a Preface
containing the same important
information as the orange cover.
Helmet Model 600
Low Pressure 6 psi to 20 psi
O. M. 23929
November, 2003
E, 03/14
WARNING

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 600 and is the answer not in the manual?

Questions and answers

Related Manuals for Clemco 600

Summary of Contents for Clemco 600

  • Page 1 © 2014 CLEMCO INDUSTRIES CORP. One Cable Car Dr. Washington, MO 63090 *If you are using a Clemco Distributor Phone (636) 239-4300 Maintenance and Part Guide, refer to (800) 726-7559 Email: info@clemcoindustries.com the orange warnings insert preceding www.clemcoindustries.com...

  • Page 2: General Instructions

    Clemco manufactures. Users must contact each Abrasive Blasting. manufacturer and supplier of products used in the blast job for Clemco Industries Corp. One Cable Car Drive Washington MO 63090 warnings, information, training, and instruction relating to the Tel: 636 239-4300 — Fax: 800 726-7559 proper and safe use of their equipment.

  • Page 3: Operational Instructions

    Numerous topics associated with the hazards of crystalline silica in silica blasting sand can be found on http:// osha.gov/. Clemco urges users of silica blasting sand to visit this website, and read and heed the information it contains.

  • Page 4: Maintenance And Repair

     Exceeding the maximum working pressure. Clemco blast machines are built to ASME-code and carry a ‘U’ or ‘UM’ stamp, and National Board/serial number. Every machine is marked with its maximum working pressure. Never exceed the maximum working pressure limits of the blast machine.
  • Page 5 Always ground the machine to eliminate hazard of static shock. Install a blast machine screen to keep out foreign objects. Use a blast machine ©Clemco Industries Corp., Stock No. 20954P, 0692 Rev. F, 06/12 cover if left outdoors overnight. Never exceed the maximum working pressure of the vessel.
  • Page 6 The Clemco Apollo Supplied-Air Respirator is manuals before setting-up and using the respirator. approved by the National Institute of Occupational Manuals for Clemco low pressure, ambient air pumps Safety and Health (NIOSH). that may be used with Apollo LP Respirators are available on our web site, www.clemcoindustries.com,...

  • Page 7: Toxic Dust Poisoning

    Lead, Silica, Antimony, Arsenic, The Apollo supplied-air respirator system is Beryllium, Cadmium, Chromium, Cobalt, Nickel, approved by NIOSH as a Type-CE, continuous-flow, © 2014 CLEMCO INDUSTRIES CORP.   Manual No. 23929, Rev. E 03/14 www.clemcoindustries.com...
  • Page 8 APF of 1000 to all Apollo National Institute for Occupational Safety and Health Series Respirators based on the simulated 4676 Columbia Parkway workplace protection factor studies Clemco has Cincinnati, OH 45226 (513) 533-8287 performed. These studies are available for download from Clemco’s Website www.clemcoindustries.com, under the “Safety...
  • Page 9 NOTE: If the respirator does not include an approved does not exceed 25 times the PEL. However OSHA's Clemco respirator hose, and if one is not at the work site 2006 revised Respirator Standard allows an exception for for use with the respirator, one or more alternate hoses type CE respirators which have validated third party must be ordered separately.
  • Page 10 Section 9.1. could permit entry of toxic and hazardous dust or abrasive into the helmet. © 2014 CLEMCO INDUSTRIES CORP.   Manual No. 23929, Rev. E 03/14 www.clemcoindustries.com...
  • Page 11 The male end attaches to the ambient air pump. CMS-3 CO Monitor Option, Respirator Mounted Connect the clamp-on The Clemco supplied air respirator model Apollo 600 LP swivel to the helmet’s is NIOSH approved with the accessory CMS-3 personal inlet fitting.

  • Page 12: Air Supply

    Carbon Dioxide ..... maximum of 1000 ppm is adjusted with static pressure (no air flow), pressure Carbon Monoxide ....maximum of 10 ppm may drop below the required pressure when the © 2014 CLEMCO INDUSTRIES CORP.   Manual No. 23929, Rev. E 03/14 www.clemcoindustries.com...

  • Page 13: Operation

    4.2.3.1 This optional accessory kit contains parts and When donning the respirator or taking it off, instructions to convert an Apollo 600 respirator from low keep it upright to prevent dust and abrasive from falling pressure (for use with an ambient air pump) to high inside.

  • Page 14: Maintenance Program

    The standard, black/grey pad is wear (See Section 6.1 for adjustment and Section 9-3 for installed in the helmet, the black/blue pad is loose. replacement). © 2014 CLEMCO INDUSTRIES CORP.   Manual No. 23929, Rev. E 03/14 www.clemcoindustries.com...

  • Page 15: Cleaning And Disinfecting

    Tumble dry in a clothes dryer at the lowest temperature setting. Do not dry clean. © 2014 CLEMCO INDUSTRIES CORP.   Manual No. 23929, Rev. E 03/14 www.clemcoindustries.com...

  • Page 16: Service & Maintenance

    9.1.1.2 Unlatch the window frame and remove remnants of old lenses. 9.1.1.3 Inspect the window gasket and inner lens. If necessary replace per Section 9.2. © 2014 CLEMCO INDUSTRIES CORP.   Manual No. 23929, Rev. E 03/14 www.clemcoindustries.com...
  • Page 17 9.2.10 Work the lens into the groove until it is 9.1.2.4 Secure the lens to the frame by pressing the completely seated into the gasket’s groove. round mounting holes onto the mushroom shaped © 2014 CLEMCO INDUSTRIES CORP.   Manual No. 23929, Rev. E 03/14 www.clemcoindustries.com...
  • Page 18 9.3.2.3 To remove the top pad, hold the air baffle Figure 4 partition (Figure 6, Item 13) in place, and pull the pad to separate it from the partition. © 2014 CLEMCO INDUSTRIES CORP.   Manual No. 23929, Rev. E 03/14 www.clemcoindustries.com...
  • Page 19 Air Baffle Partition Tuck tensioning strip under window frame. 9.9.1 Remove the cape and suspension per Sections Figure 5 9.3 and 9.4. © 2014 CLEMCO INDUSTRIES CORP.   Manual No. 23929, Rev. E 03/14 www.clemcoindustries.com...

  • Page 20: Replacement Parts

    Supplied-Air Respirator Systems and Accessories Respirator Systems Description Stock No. Apollo 600 LP Respirator with Web Suspension less respirator hose .......... 24010 with 50-foot respirator hose ......24011 Apollo 600-LP DLX Respirator with Padded Suspension less respirator hose .......... 25195 with 50-foot respirator hose ......
  • Page 21 1-inch x 3-feet long........24656 Outer lens, .015", rectangular, pkg. of 25 . 24005 Alternate DLX Padded Suspension Some items are rotated for clarity Figure 6 © 2014 CLEMCO INDUSTRIES CORP.   Manual No. 23929, Rev. E 03/14 www.clemcoindustries.com...

Table of Contents