Advertisement
USB Operation
Play MP3/WMA music inside a USB stick. Insert the USB stick with MP3
/WMA musics into the USB port, it will play automatically.
Note: the USB port also supports charging mobile phone, the maximum
charging ability is 5V/1A.
Select Next Track or Previous Track
In the USB mode, briefly press the
or
button to play the the next or
previou track.
Fast Forward/Reverse
Press and hold the
or
button to fast forward or reverse a track.
Play / Pause
Press the
button to interrupt the playback of a music (pause function).
Press this button again to continue the playback.
Introduction Scan
Press the INT button to play the first 10 seconds of each track.
Press again to stop the introduction scan, and play the current track.
Repeating the track
Press the RPT button to toggle between RPT ONE (Continuously repeat
current track) and RPT FOD (Continuously repeat all tracks in current folder),
RPT ALL (Play all track).
Playing all tracks in random
Press RDM once, play all tracks randomly.
Press RDM once again, exit from random playback.
Track/Folder Navigation
- Press the -10/+10 buttons to jump 10 tracks backward or forward.
It is required that over 10 tracks be available on the storage medium.
- Press and hold the -10/+10 button to select the previous or the next folder.
(If there are folders on the storage medium.)
Select the track or file for playback in MP3 format
a) Press and hold the
button to enter track search mode.
b) Rotate the volume knob to select the number of your favorite track with
high speed.
c) When the desired track number appears, confirm your selection by
pressing the VOL knob.
Remote Control
1.
(Power on/off) button
2. VOL+/VOL-(volume increase/decrease) button
3. Band button,
(answer call) button
4. PREV: tune down, seek down;
Track down, fast reverse
5. SEL(selection) button
6. NEXT: tune up, seek up;
Track up, fast forward
7. Mute button, DEL(Delete) button
8. CLK(clock setting) button,
(end call) button
9.
button, preset station 1 button,
keypad 1
10. INT(intro) button, preset station 2 button,
keypad 2
11. RPT(repeat) button, preset station 3 button,
keypad 3
12. RDM(random), preset station 4 button, keypad 4
13. -10(previous 10 tracks), preset station 5 button, keypad 5
14. +10(next 10 tracks), preset station 6 button, keypad 6
15. ST(stereo) button, keypad 7
16. LOUD(loudness) button, keypad 8
17. AMS(automatic music search) button, keypad 9
18. SRC(Source) button, keypad *
19. EQ(Equalizer) button, keypad 0
20. LOC(local)/DX button, keypad #
Note: When using the remote control for the first time, you must pull out the
portective plastic tab from the battery compartment found on the back of the
remote control.
Bluetooth Operation
Pair and Connect
Pair the mobile phone with the device before using it.
1. In any mode, prior to pairing and connecting, the BT logo is flashing in the
LCD indicating that no device is connected. To begin pairing, enable BT
mode on your mobile phone.
2. When the phone finds the car audio system, "BOSS AUDIO MR500UAB"
name will be displayed.
3. Choose the "BOSS AUDIO MR500UAB" from the device list to pair and
connect with the car audio system. Upon confirming, the BT logo will stop
flashing.
4. When pairing is complete, the mobile phone audio will automatically
transfer to the car audio system whenever a call is made or received, or
when the mobile phone plays music.
Disconnect or reconnect the bluetooth connection
Press and hold the
connection.
Answer a Call
• When the mobile phone is called, the incoming telephone number displays
on the LCD.
• To receive the call, press the
Reject or End a Call
To reject or end the call, press the
Redial Last Dialed Number
Press the
Switch Audio Between Car Audio and mobile Phone
During a call, press the VOL knob/button to switch the audio source from the
car audio system back to your mobile phone.
To make a call with this bluetooth handsfree system:
a) When linking up the Bluetooth-enabled mobile phone to this bluetooth
handsfree system, press the # button on remote control to access the dial
telephone number mode, then press the "0~9", * and # button on remote
control to input the telephone number, and the entered number will be
shown on the LCD display.
b) If a number has been incorrectly inputted, press the DEL button on the
remote control to delete it.
Specifications
General
Power supply Requirement :
Maximum power output :
Speaker impedance :
1
3
Unit Dimensions(WxHxD) :
5
2
Weight :
4
6
Fuse :
7
8
RADIO
9
11
10
FM
12
14
13
16
Frequency Range:
15
17
Channel step:
18
20
19
AM
Frequency Range:
Channel step:
USB
Usable Audio Formats:
USB Port Type:
USB Charging:
Pre-amp Output:
Frequency Response:
S/N Ratio:
BT
BT Profile supports:
Range of frequency:
button to disconnect or reconnect the bluetooth
button on the front panel.
button.
button to redial the last dialed phone number.
DC 12V
50W X 4CH
4 - 8 Ohm
7.0 X 2.0 X 2.76 inches
0.84 lbs
10 A
87.5 MHz - 107.9 MHz (USA)
87.5 MHz - 108.0 MHz (EUROPE)
200 KHz (USA)
50 KHz (EUROPE)
530 KHz - 1710 KHz (USA)
522-1620 KHz (EUROPE)
10 KHz (USA)
9 KHz (EUROPE)
MP3/WMA
2.0
5V/1A
Front and Rear
20 Hz - 20KHz
60dB
Headset, Handsfree and A2DP & AVRCP
2.4GHz
Bluetooth Operation
c) Press the
button to make outgoing call.
Audio Streaming (A2DP)
The unit supports A2DP (advanced audio distribution profile) wireless
streaming audio from your Bluetooth mobile device directly to your head unit.
You can also control your music from the front panel of the head unit using
AVRCP (audio video remote control profile).
1. After pairing, connecting and enabling streaming audio from a compatible
mobile device,
press the SRC button to enter BT mode and the "BT AUDIO" will be shown
on the LCD display.
2. When a mobile device is paired, music played through that device will
automatically be heard through the car audio system.
3. Press the
or
button to play the next or previous on the mobile
phone.
4. Press the
button to pause or resume music playback.
Push-To-Talk
This Push-To-Talk feature allows direct access to Android and IOS smart-
phones voice assistant capability when user establish the bluetooth
connection between user's smartphone and this receiver.
Simply connect directly from this receiver via Bluetooth with
(VOL knob).
Note:
Before using the Push-To-Talk, user must enable the mobile data on user's
smartphone.
To use the navigation feature, switch to the BT Audio source to hear voice
commands over your vehicles speakers.
button
Advertisement
