Interchangeable lens for digital camera (72 pages)
Summary of Contents for Panasonic H-FS1442APP
Page 1
Order No.DSC1302014CE Interchangeable Lens for Digital Camera H-FS1442APP Model No. H-FS1442AE H-FS1442AGK Colour (S)....Silver Type (K)....Black Type file:///C|/U...emp/Rar$EXa0.829/viewing/SGML_VIEW_DATA/ALL/H-FS1442APP/SVC/DSC1302014CE/doc/DSC1302014CE_cvr.xml[11/12/2018 11:14:52 AM]...
Therefore, any needs of the "LENS MAIN UNIT" (Ref. 208), carefully confrm its performance in advance. 2. Once "LENS MAIN UNIT" (Ref. 208) is confrmed as defective, place order "LENS Unit" (Ref. 200) and replace SHADING FRAME (Ref. 202), to maintain Serial number of owner's original lens. file:///C|/U...emp/Rar$EXa0.829/viewing/SGML_VIEW_DATA/ALL/H-FS1442APP/SVC/DSC1302014CE/doc/DSC1302014CE_01.xml[11/12/2018 11:15:49 AM]...
Page 4
3. No adjustment is required when replacing the part mentioned on Fig.1-1. But, when tighten the concerned screws,apply proper torque mentioned on "4. Disassembly and Assembly Instruction" section. file:///C|/U...emp/Rar$EXa0.829/viewing/SGML_VIEW_DATA/ALL/H-FS1442APP/SVC/DSC1302014CE/doc/DSC1302014CE_01.xml[11/12/2018 11:15:49 AM]...
2 Operating Guide 2.1 Before Use (Information for Your Safety) 2.2 Cautions For Use file:///C|/U...emp/Rar$EXa0.829/viewing/SGML_VIEW_DATA/ALL/H-FS1442APP/SVC/DSC1302014CE/doc/DSC1302014CE_02.xml[11/12/2018 11:16:56 AM]...
10,000 (Federal Standard 209D). (When cleaning the inside of a lens, it is indispensable.) [NOTE] Work in the environment of satisfed clean level less than class 10,000 (Federal Standard 209D) when cleaning the inside of a lens. file:///C|/U...emp/Rar$EXa0.829/viewing/SGML_VIEW_DATA/ALL/H-FS1442APP/SVC/DSC1302014CE/doc/DSC1302014CE_03.xml[11/12/2018 11:17:41 AM]...
1. When installing the screws, be sure to use the torque driver (RFKZ0456) and tighten the screws with specifed torque, mentioned on the following table. 2. Use VFK1390 (small driver) when screwing Ref. B213. Interchangeable Lens (H-FS1442A) file:///C|/U...emp/Rar$EXa0.829/viewing/SGML_VIEW_DATA/ALL/H-FS1442APP/SVC/DSC1302014CE/doc/DSC1302014CE_04.xml[11/12/2018 11:18:42 AM]...
1. Decoration ring is sticked on the 1st lens frame unit. 2. Put the sheet so that the lens glass is fully covered. 3. Insert the small fat blade screwdriver to Gap(between the decoration ring and lens glass), and peel off the decoration ring gently. file:///C|/U...emp/Rar$EXa0.829/viewing/SGML_VIEW_DATA/ALL/H-FS1442APP/SVC/DSC1302014CE/doc/DSC1302014CE_04.xml[11/12/2018 11:18:42 AM]...
Page 11
4.2.2 Removal of the 1st lens frame unit 1. Remove the 3 screws (A). 4.2.3 Removal of the Shading frame 1. Remove the 3 screws (B). file:///C|/U...emp/Rar$EXa0.829/viewing/SGML_VIEW_DATA/ALL/H-FS1442APP/SVC/DSC1302014CE/doc/DSC1302014CE_04.xml[11/12/2018 11:18:42 AM]...
Page 12
4.2.4 Removal of the L mount unit 1. Remove 1 screw (C) and 3 screws (D). 2. Insert 3 adjustment shafts(VMS7941 or an equivalent one) to screw holes in order not to remove Back adjust-ment washers.Then, remove the L mount unit. file:///C|/U...emp/Rar$EXa0.829/viewing/SGML_VIEW_DATA/ALL/H-FS1442APP/SVC/DSC1302014CE/doc/DSC1302014CE_04.xml[11/12/2018 11:18:42 AM]...
Page 13
4.2.5 Removal of the Rear frame unit 1. Remove 4 screws (E). 4.2.6 Removal of the Lens P.C.B.unit and the Lens mount contact unit 1. Disconnect 4 connectors. 4.2.7 Removal of the Lens mount contact unit file:///C|/U...emp/Rar$EXa0.829/viewing/SGML_VIEW_DATA/ALL/H-FS1442APP/SVC/DSC1302014CE/doc/DSC1302014CE_04.xml[11/12/2018 11:18:42 AM]...
Use new one, do not use the one which is removed. Double-stick tape sticks to the Decoration ring of therepair part. Please remove the old double-stick tape from the Lenstop unit. 2. After installing the Decoration ring, use a soft cloth to press it into place. file:///C|/U...emp/Rar$EXa0.829/viewing/SGML_VIEW_DATA/ALL/H-FS1442APP/SVC/DSC1302014CE/doc/DSC1302014CE_04.xml[11/12/2018 11:18:42 AM]...
Page 15
4.3.3 Installation of the Lens mount contact unit 1. Connect 1 connector. 4.3.4 Installation of the Lens P.C.B.unit and the Lens mount contact unit 1. Connect 4 connectors. file:///C|/U...emp/Rar$EXa0.829/viewing/SGML_VIEW_DATA/ALL/H-FS1442APP/SVC/DSC1302014CE/doc/DSC1302014CE_04.xml[11/12/2018 11:18:42 AM]...
Page 16
1. Tighten 4 screws (E) in numerical order by using the torque driver with specifed torque. (Torque Driver : RFKZ0456) (Torque : 8 ± 0.5N cm) 4.3.6 Installation of the L mount unit 1. Install the L mount unit. Then, remove 3 adjustment shafts(VMS7941 or an equivalent one). file:///C|/U...emp/Rar$EXa0.829/viewing/SGML_VIEW_DATA/ALL/H-FS1442APP/SVC/DSC1302014CE/doc/DSC1302014CE_04.xml[11/12/2018 11:18:42 AM]...
Page 17
(Torque for screw (D) : 16±0.5N cm) 4.3.7 Installation of the Shading frame 1. Tighten 3 screws (B) in numerical order by using the torque driver with specifed torque. (Torque Driver : RFKZ0456) (Torque for screw (B) : 7.5±0.5N cm) file:///C|/U...emp/Rar$EXa0.829/viewing/SGML_VIEW_DATA/ALL/H-FS1442APP/SVC/DSC1302014CE/doc/DSC1302014CE_04.xml[11/12/2018 11:18:42 AM]...
(Consult the Instruction sheet which is included in the Lens cleaning KIT in details.) 2. When it is inside of the lens When there is dust / dirt inside surface of the 1st lens frame unit and 8th lens, remove it by referring to the following procedures. file:///C|/U...emp/Rar$EXa0.829/viewing/SGML_VIEW_DATA/ALL/H-FS1442APP/SVC/DSC1302014CE/doc/DSC1302014CE_05.xml[11/12/2018 11:19:47 AM]...
Page 20
So the 1st lens frame unit and 8th lens is not supplied as spare parts. Also do not exchange the 1st lens frame unit and 8th lens taking from others. 4. When clean inside 8th lens, blow out dust by gas duster at Tele side. (Refer to the following picture.) file:///C|/U...emp/Rar$EXa0.829/viewing/SGML_VIEW_DATA/ALL/H-FS1442APP/SVC/DSC1302014CE/doc/DSC1302014CE_05.xml[11/12/2018 11:19:47 AM]...
Page 21
Print Parts List Model No. : H-FS1442APP/E/GK Frame and Casing Section Model No. : H-FS1442APP/E/GK Packing Parts and Accessories file:///C|/U...al/Temp/Rar$EXa0.356/viewing/SGML_VIEW_DATA/ALL/H-FS1442APP/SVC/DSC1302014CE/mec2/en/html/print_all.htm[11/12/2018 2:41:29 PM]...
Page 22
Print Parts List Model No. : H-FS1442APP/E/GK Parts List Ref. Change Safety Part No. Part Name & Description Q'ty Remarks VXW1562 LENS UNIT 1 (-K) VXW1566 LENS UNIT 1 (-S) ----- SHADING FRAME 1 (NOT SUPPLIED) VEJ2337 LENS MOUNT CONTAT UNIT...
Need help?
Do you have a question about the H-FS1442APP and is the answer not in the manual?
Questions and answers